SKU: 1378-604
Finish: Chrome
Keyed locking for maximum security
Requires 3/4” mounting hole
For wood or metal door or drawer
2 washers for 90 or 180 degree rotation
Max drawer thickness 1/2”
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$9.19
SKU: 1321
Finish: Polished Brass
Easy to install replacement
Brass plated steel
Key cylinder is offset from center
5/16” Bolt
Instructions:
1. Remove old mailbox lock by removing screw.
2. Position lock on mailbox and re-install screws.
$5.89
SKU: 1281-601
Finish: Polished Brass
Keyed locking for maximum security
Requires 3/4” mounting hole
For wood or metal door or drawer
2 washers for 90 or 180 degree rotation
Max drawer thickness 3/4”
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$11.39
SKU: 1278-601
Polished Brass
Keyed locking for maximum security
Requires 3/4” mounting hole
For wood or metal door or drawer
2 washers for 90 or 180 degree rotation
Max drawer thickness 1/2
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$10.69
SKU: 1277
Finish: White
For home & travel
Easy to use
Installs in seconds
Secures your door from an unwanted
entry
Heavy gauge steel construction
Instructions:
1. Align arrow on fork with holes in bottom section.
2. Adjust guard to proper height of door handle. To secure length, rotate inner section until pin pop up through hole in outer section.
3. Place forked end under door handle and set guard foot 10-12″ from bottom of door. Lightly tap end with your foot toward door to secure.
4. To remove: A light tap of foot against door guard away from door will loosen guard.
$29.99
SKU: 1253-604
Finish: Aluminum Tone
Securely locks in closed or vented
position
Assembled with hardened steel bolt
Easily activated with foot
Locks/unlocks with key
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$13.79
SKU: 1146
Finish: White
For old style passage locks
Screw mounted on door
Dimensions: 2-1/2” diameter
Fits up to 1-1/2″ diameter bore
Instructions:
1. Remove door knob and old roses.
2. Replace with new roses by lining up the holes and attaching screws. Attach door knobs.
$3.99
SKU: 1145
Finish: White
Pair with spindle & roses
For old style passage locks
Spindle size: 7mm
Instructions:
1. Remove old knobs and spindle.
2. Twist one knob onto spindle and slide through door. Twist other knob on other side of spindle.
$11.89
SKU: 1143
Finish: Polished Brass
For old style passage locks
Dimensions: 2-1/2” diameter roses
Spindle size: 7mm
Fits up to 1-1/2″ diameter bore
Instructions:
1. Remove old hardware from door.
2. Attach new roses with screws provided.
3. Twist one knob onto spindle and slide through door hole while attaching to rose.
4. Twist last knob onto spindle and rose. Tighten knows using small screws on the side of knobs.
$27.99
SKU: 1125
Finish: Brass Tone
5-pin tumbler with hardened steel pins
Dual single or double cylinder locking unit & strike
Locks door to jamb to prevent forced
entry
Door Thickness: 1-3/8″ to 2-1/4″
1-1/4″ bore required
Key Blank: Weiser Blank WR2/WR3
Instructions:
CAUTIONS: Do not unscrew small retaining screws at rear of cylinder. Use only dry lubricant (graphite) on locks. Keep away clear of foreign objects.
To Install:
1. Select convenient height for lock and place template against edge of door.
2. Mark hole positions. Bore 1-3/8″ hole for cylinder where indicated. Note: Bore through door until tip of drill barely emerges from other side. Remove drill bit and complete hole by drilling from opposite side to reduce splintering.
3. Drill 3/32″ diameter holes 1/2″ deep from attachment screws.
4. Insert cylinder and trim ring from outside of door. Attach backplate with two connecting bolts. Note: If bolts are too long, saw or break at groove, using caution to avoid marring the thread.
5. Cut or break connecting bar so it projects 3/8″ to 1/2″ beyond the inside of the door.
6. Plack lock on door so connecting bar enters “X” slot in back of lock. Secure with large mounting screws.
7. Align strike carefully, using template as a guide. Draw outline of strike on door jamb trim and chisel wood away (mortise) so strike mates freely with locking bars.
8. Mark mounting homes for strike, dill pilot holes, and secure strike to door jamb with screws provided.
$46.99
SKU: 1106
Finish: White
Latch hold-back (prevents locking
yourself out)
5-pin tumbler with hardened steel pins
Door Thickness 1-3/8″ to 2-1/4″
1-1/4” bore required
Spring latch for automatic locking
Instructions:
1. At desired height bore the hole for the cylinder 1-1/4″ diameter, with center at a distance of 2-3/8″ from edge of door.
2. Insert cylinder and ring from the outside of door and place back plate on inside of door. Connect back plate to cylinder with two connecting screws. Cut screws to proper length relative to door thickness.
3. Cut off connecting bar so that it projects 3/8″ beyond inside of door.
4. Place lock on door so that connecting bar enters slot. Mark holes. Remove lock and drill 1/8″ pilot holes. Attache lock to door by inserting screws through lock into door.
5. Place strike plate on door jamb. Mark holes. Remove strike place and drill 1/8″ pilot holes.
6. As needed, use chisel to cut door jamb so that strike is flush with door jamb.
$29.99
SKU: 1050
Finish: Polished Brass
1/4” adjustment for tight fit of door to frame
Stops door rattle
Assures engagement of dead latch function
Residential or commercial frames
Dimensions: 1-1/4” x 4-7/8”
Door Thickness: All
Instructions:
Before starting first check door thickness for proper template alignment and then follow installation instructions.
-If door thickness is 1-3/4″ place template on from 3/16″ from door jamb.
-If door thickness is 1-3/8″ place template on the door jamb.
1. Remove old strike.
2. Center template with latch hole and tape in place.
3. Position new strike in place and mark two holes. Chisel out area behind strike if needed or a flush fit is desired.
4. Drill 1/8″ pilot holes 2″ deep. Adjust to fit door.
$7.49
SKU: 1047
Finish: Polished Brass
2-1/2” extended lip
1/4” adjustment for tight fit of door to frame
Stops door rattle
Assures engagement of dead latch function
Use on wood frames
Door Thickness: All
Dimensions: 2-3/4″ x 3″
$7.39
SKU: 1016-PB
Finish: Polished Brass
Replaces most deadbolt strikes for increased security
Strengthens or repairs wood jambs
3” screws attach to wall stud for increased security
Dimensions: 1-5/8” x 11”
Door Thickness: 1-3/4″ or thicker
Instructions:
1. Remove old strike.
2. Position new strike in place and mark the two mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or if a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install small screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike plate and retest.
$8.69
SKU: 1306
Finish: Chrome
Chrome-plated steel
Ideal for cabinets & cases with sliding glass doors
Adjustable length for many alignments
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
Instructions:
1. Slide outside door to open position. Place lock on inside door as shown and tighten screw. To avoid breaking glass, do not over-tighten.
2. Close sliding doors completely.
3. Slide lock over notched locking plate, fitting the flat side against outside door edge.
$7.59
SKU: 1150
Finish: Polished Brass
Zinc housing
5-pin tumbler lock
1-1/4″ bore hole required
Replacement lock cylinder for rim cylinder type lock sets
Key Blank: Weiser Blank WR5
Instructions:
1. Remove screws from old cylinder and remove cylinder.
2. Align connecting spindles of replacement cylinder to lock.
3. Insert screws into cylinder and tighten.
$10.39