$7.49
SKU: 1050
Finish: Polished Brass
1/4” adjustment for tight fit of door to frame
Stops door rattle
Assures engagement of dead latch function
Residential or commercial frames
Dimensions: 1-1/4” x 4-7/8”
Door Thickness: All
Instructions:
Before starting first check door thickness for proper template alignment and then follow installation instructions.
-If door thickness is 1-3/4″ place template on from 3/16″ from door jamb.
-If door thickness is 1-3/8″ place template on the door jamb.
1. Remove old strike.
2. Center template with latch hole and tape in place.
3. Position new strike in place and mark two holes. Chisel out area behind strike if needed or a flush fit is desired.
4. Drill 1/8″ pilot holes 2″ deep. Adjust to fit door.
In stock
Add to Compare
SKU: 1105, 1105-SN
Finishes: Polished Brass & Satin Nickel
Latch hold-back (prevents locking yourself out)
5-pin tumbler with hardened steel pins
1-1/4″ bore required
Spring latch for automatic locking
Door Thickness: 1-3/8″ to 2-1/4″
Key Blank: Weiser Blank WR2/WR3
Instructions:
1. At desired height bore the hole for the cylinder 1-1/4″ diameter, with center at a distance of 2-3/8″ from edge of door.
2. Insert cylinder and ring from he outside of door and place back plate on inside of door. Connect back plate to cylinder with two connecting screws. Cut screws to proper length relative to door thickness.
3. Cut off connecting bar so that it projects 3/8″ beyond inside of door.
4. Plack lock on door so that connecting bar enters slot. Mark holes. Remove lock and drill 1/8″ pilot holes. Attache lock to door by inserting screws through lock into door.
5. Place strike plate on door jamb. Mark holes. Remove strike plate and drill 1/8″ pilot holes.
6. As needed, use chisel to cut door jamb so that strike is flush with door jamb.
$37.09
SKU:1129
Finish: Polished Brass
Knobs and trim plates
Case-hardened steel case
Lock bolt is key activated both inside & outside
Bolt reversible to left and right handed door
Requires mortise cutout
Replaces most bit key mortise locks with 2-1/4″ backset
Instructions:
1. Fold template (see insert included) along dotted line and wrap around inside edge of door at a convenient height. mark holes A and B through template.
2. Position vertical line C in center of door thickness and mark holes as shown. Be sure the template does not move up or down.
3. Remove template and drill seven 5/8″ diameter holes 3″ into edge of door where C holes were drawn. Chisel out remaining wood to form a pocket in the edge of the door measuring 5/8″ wide by 4-1/8″ long by 3″ deep.
4. Drill one 3/4″ hole on mark A through the door. Drill four 5/16″ holes as indicated through the door to form slot B.
5. Insert mortise lock into pocket, draw a line around the face plate, and remove lock. Chisel out the wood within the lines to a depth of approximately 3/32″. Insert lock occasionally to ensure proper depth.
6. Insert lock into door and attach with two flathead screws.
7. Position trim plates on door in line with lock and attach using eight oval-head screws.
8. Insert spindle through hole A and attach knobs at each end of spindle.
9. Position strike in line with latch and attach with two flathead screws.
$41.99
SKU: 1120
Finish: Polished Brass
5-pin tumbler with hardened steel pins
Single cylinder locking unit & strike
Locks door to jamb to prevent forced entry
1-1/4″ bore required
Includes tamper-resistant shutter guard
Door Thickness: 1-3/8″ to 2-1/4″
Key Blank: Weiser Blank WR2/WR3
Instructions:
CAUTION: Do not unscrew small retaining screws at rear of cylinder. Use only dry lubricant (graphite) on lock. Keep keyway clear of foreign objects.
1. Select convenient height for lock and place template against edge of door.
2. Mark hole positions. Bore 1-3/8″ hole for cylinder where indicated. Note: Bore through door until tip of drill barely emerges from other side. Remove drill bit and complete hole by drilling from opposite side to reduce splintering.
3. Drill 3/32″ diameter holes 1/2″ deep for attachment screws.
4. Insert cylinder and trim ring from outside of door. Attache backplate with two connecting bolts. Note: If bolts are too long, saw or break at groove, using caution to avoid marring the thread.
5. Cut or break connecting bar so it projects 3/8″ to 1/2″ beyond the inside of the door.
6. Plack lock on door so connecting bar enters “X” slot in back of lock. Secure with large mounting screws.
7. Align strike carefully, using template as a guide. Draw outline of strike on door jamb trim and chisel wood away (mortise) so strike mates freely with locking bars.
8. Mark mounting holes for strike, drill pilot holes, and secure strike to door jamb with screws provided.
$28.89
SKU: 1047
Finish: Polished Brass
2-1/2” extended lip
1/4” adjustment for tight fit of door to frame
Stops door rattle
Assures engagement of dead latch function
Use on wood frames
Door Thickness: All
Dimensions: 2-3/4″ x 3″
$7.39
SKU: 1089, 1089-SSS
Finishes: Polished Brass
Out-swinging doors only
Secures against forced entry
Protects latch or bolt
Residential or commercial use
Dimensions: 3″ x 7″
Backset: Locksets with 2-3/4″ backset
Instructions:
1. Place latch guard on door and center on lock.
2. Mark center of mounting holes.
3. Drill two 3/8″ holes through door.
4. Install bolts, washers and nuts. Tighten securely.
$13.79
