SKU: 1050
Finish: Polished Brass
1/4” adjustment for tight fit of door to frame
Stops door rattle
Assures engagement of dead latch function
Residential or commercial frames
Dimensions: 1-1/4” x 4-7/8”
Door Thickness: All
Instructions:
Before starting first check door thickness for proper template alignment and then follow installation instructions.
-If door thickness is 1-3/4″ place template on from 3/16″ from door jamb.
-If door thickness is 1-3/8″ place template on the door jamb.
1. Remove old strike.
2. Center template with latch hole and tape in place.
3. Position new strike in place and mark two holes. Chisel out area behind strike if needed or a flush fit is desired.
4. Drill 1/8″ pilot holes 2″ deep. Adjust to fit door.
$7.49
SKU: 1047
Finish: Polished Brass
2-1/2” extended lip
1/4” adjustment for tight fit of door to frame
Stops door rattle
Assures engagement of dead latch function
Use on wood frames
Door Thickness: All
Dimensions: 2-3/4″ x 3″
$7.39
SKU: 1016-PB
Finish: Polished Brass
Replaces most deadbolt strikes for increased security
Strengthens or repairs wood jambs
3” screws attach to wall stud for increased security
Dimensions: 1-5/8” x 11”
Door Thickness: 1-3/4″ or thicker
Instructions:
1. Remove old strike.
2. Position new strike in place and mark the two mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or if a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install small screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike plate and retest.
$8.69
SKU: 1090
Finish: Chrome
Out-swinging doors only
Secures against forced entry
Protects latch or bolt
Residential or commercial use
Dimensions: 3″ x 7″
Backset: Locksets with 2-3/4″ backset
Instructions:
1. Place latch guard on door and center on lock.
2. Mark center of mounting holes.
3. Drill two 3/8″ holes through door.
4. Install bolts, washer and nuts. Tighten securely.
Note: If latch guard contacts strike lip, bend in slightly with hammer.
$13.79
SKU: 1089, 1089-SSS
Finishes: Polished Brass
Out-swinging doors only
Secures against forced entry
Protects latch or bolt
Residential or commercial use
Dimensions: 3″ x 7″
Backset: Locksets with 2-3/4″ backset
Instructions:
1. Place latch guard on door and center on lock.
2. Mark center of mounting holes.
3. Drill two 3/8″ holes through door.
4. Install bolts, washers and nuts. Tighten securely.
$13.79
SKU: 1085, 1085-SSS
Finishes: Polished Brass & Solid Stainless Steel
Out-swinging doors only
Secures against forced entry
Protects latch or bolt
Dimensions: 2-1/2″ x 6″
Backset: Locksets with 2-3/8″ backset
Instructions:
1. Place latch guard on door, center on lock.
2. Mark center of mounting holes.
3. Drill two 3/8″ holes through door.
4. Install bolts, washer, and nuts. Tighten securely.
Note: If latch guard contacts strike lip, bend in slightly with hammer.
$13.79
SKU: 1063, 1064, 1065, 1065-SN, 1066
Finishes: Vintage Bronze, Antique Brass, Polished Brass, Satin Nickel & Chrome
Fits Standard size doors
Steel strike plate with adjustable tab
Replaces most residential exterior & interior strikes
Dimensions: 1-3/8″ x 2-1/4″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Place new strike on door jamb, centered with latch hole.
3. Install screws provided and adjust tab with screw driver for proper fit.
$4.49 – $5.09
SKU: 1045
Finish: Polished Brass
1/4″ adjustment for tight fit of door to frame
Stops door rattle
Assures engagement of dead latch function
Residential or commercial frames
Dimensions: 1-1/4″ x 2-3/4″
Door Thickness: All
Instructions:
Before starting first check door thickness for proper template alignment and then follow installation instructions.
-If door thickness is 1-3/4″ place template frame 3/16″ from door jamb.
-If door thickness is 1-3/8″ place template on the door jamb.
Installation Instructions:
1. Remove old strike.
2. Center template with latch hole and tape in place.
3. Position new strike in place and mark two holes. Chisel out area behind strike if needed or a flush fit is desired.
4. Drill 1/8″ pilot holes 2″ deep. Adjust to fit door.
$6.89
SKU: 1041, 1041-SN
Finish: Polished Brass, Solid Stainless Steel, Vintage Bronze, Chrome & Satin Nickel
Fits standard size doors
Use on wood or metal jambs
Common replacement for most Grade 2 & 3 locksets
Dimensions: 1-1/8″ x 2-3/4″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Place new strike on door jamb centered with latch hole.
3. Install screws provided and adjust tab with screw driver for proper fit.
$6.89
SKU: 1038
Finish: Stainless Steel
Use on wood or metal jambs
Works with most commercial Grade 1 lock sets
Dimensions: 1-1/4″ x 4-7/8″
Door Thickness: All
Instructions:
1. Remove old strike
2. Place strike on jamb, centered over latch hole.
3. Mark outline of strike on door jamb.
4. Using chisel, cut out area for strike 1/16″ deep.
5. Install screws.
$8.09
SKU: 1035, 1036
Finish: Polished Brass & Chrome
Fits standard size doors
Use on wood or metal jambs
Dimensions: 4-7/8″ long, 3-3/8″ lip
Door Thickness: All
Instructions:
1. Place strike on jamb, centered over latch hole.
2. Mark outline of strike on door jamb.
3. Using chisel, cut out area for strike 1/16″ deep.
4. Install screws.
$6.89
SKU: 1027
Finish: Polished Brass
For locks with 5-1/2″ to 6″ centers
Replaces standard latch & deadbolt
strikes with one piece security
Strengthens or repairs wood jambs
3″ screws attach to wall stud for extra security
Dimensions: 1-5/8″ x 11″
Door Thickness: 1-3/4″ or thicker doors
Instructions:
1. Remove old strike
2. Position new strike in place and mark with a pencil the three mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install short screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike plate and retest.
Note: Check distance between door and frame when door is closed.
– If the gap is 1/4″ or more install strike on surface of frame.
– If the gap is less than a 1/4″ strike must be chiseled into the frame.
$14.99
SKU: 1025, 1025-SSS, 1025-VB
Finishes: Polished Brass, Solid Stainless Steel & Vintage Bronze
Fits standard size doors
Strengthens or repairs wood jambs
3″ screws attach to wall stud for extra security
Dimensions: 1-1/4″ x 8″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Position new strike in place and mark the two mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or if a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install small screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike place and retest.
$11.49
SKU: 1005
Finish: Polished Brass
Fits standard size doors
Mortising required
Screws at base of box strike secure to
2″ x 4″ framing for added security
Dimensions: 1-1/4″ x 4-7/8″
Door Thickness: All
Instructions:
1. Mark center of bolt on frame.
2. Cut out template (see insert), locate center mark on template with center mark on frame. Tape in place.
3. Draw around outside of template. Mark 4 holes through template. Drill 1″ holes per template.
4. Chisel out between 1″ holes and fit strike box.
5. Chisel out 1/8″ deep for strike.
6. Install strike and faceplate with top and bottom screws. (Be sure 2 holes in strike box are toward center of frame.)
7. Drill two 1/8″ pilot holes at bottom of strike box toward center of frame and install screws at an angle.
$8.49