$26.99
SKU: 1089, 1089-SSS
Finishes: Polished Brass
Out-swinging doors only
Secures against forced entry
Protects latch or bolt
Residential or commercial use
Dimensions: 3″ x 7″
Backset: Locksets with 2-3/4″ backset
Instructions:
1. Place latch guard on door and center on lock.
2. Mark center of mounting holes.
3. Drill two 3/8″ holes through door.
4. Install bolts, washers and nuts. Tighten securely.
SKU: 1035, 1036
Finish: Polished Brass & Chrome
Fits standard size doors
Use on wood or metal jambs
Dimensions: 4-7/8″ long, 3-3/8″ lip
Door Thickness: All
Instructions:
1. Place strike on jamb, centered over latch hole.
2. Mark outline of strike on door jamb.
3. Using chisel, cut out area for strike 1/16″ deep.
4. Install screws.
$9.99
SKU: 1005
Finish: Polished Brass
Fits standard size doors
Mortising required
Screws at base of box strike secure to
2″ x 4″ framing for added security
Dimensions: 1-1/4″ x 4-7/8″
Door Thickness: All
Instructions:
1. Mark center of bolt on frame.
2. Cut out template (see insert), locate center mark on template with center mark on frame. Tape in place.
3. Draw around outside of template. Mark 4 holes through template. Drill 1″ holes per template.
4. Chisel out between 1″ holes and fit strike box.
5. Chisel out 1/8″ deep for strike.
6. Install strike and faceplate with top and bottom screws. (Be sure 2 holes in strike box are toward center of frame.)
7. Drill two 1/8″ pilot holes at bottom of strike box toward center of frame and install screws at an angle.
$12.99
SKU: 1045
Finish: Polished Brass
1/4″ adjustment for tight fit of door to frame
Stops door rattle
Assures engagement of dead latch function
Residential or commercial frames
Dimensions: 1-1/4″ x 2-3/4″
Door Thickness: All
Instructions:
Before starting first check door thickness for proper template alignment and then follow installation instructions.
-If door thickness is 1-3/4″ place template frame 3/16″ from door jamb.
-If door thickness is 1-3/8″ place template on the door jamb.
Installation Instructions:
1. Remove old strike.
2. Center template with latch hole and tape in place.
3. Position new strike in place and mark two holes. Chisel out area behind strike if needed or a flush fit is desired.
4. Drill 1/8″ pilot holes 2″ deep. Adjust to fit door.
$9.99
SKU: 1016-PB
Finish: Polished Brass
Replaces most deadbolt strikes for increased security
Strengthens or repairs wood jambs
3” screws attach to wall stud for increased security
Dimensions: 1-5/8” x 11”
Door Thickness: 1-3/4″ or thicker
Instructions:
1. Remove old strike.
2. Position new strike in place and mark the two mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or if a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install small screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike plate and retest.
$12.99
SKU:1129
Finish: Polished Brass
Knobs and trim plates
Case-hardened steel case
Lock bolt is key activated both inside & outside
Bolt reversible to left and right handed door
Requires mortise cutout
Replaces most bit key mortise locks with 2-1/4″ backset
Instructions:
1. Fold template (see insert included) along dotted line and wrap around inside edge of door at a convenient height. mark holes A and B through template.
2. Position vertical line C in center of door thickness and mark holes as shown. Be sure the template does not move up or down.
3. Remove template and drill seven 5/8″ diameter holes 3″ into edge of door where C holes were drawn. Chisel out remaining wood to form a pocket in the edge of the door measuring 5/8″ wide by 4-1/8″ long by 3″ deep.
4. Drill one 3/4″ hole on mark A through the door. Drill four 5/16″ holes as indicated through the door to form slot B.
5. Insert mortise lock into pocket, draw a line around the face plate, and remove lock. Chisel out the wood within the lines to a depth of approximately 3/32″. Insert lock occasionally to ensure proper depth.
6. Insert lock into door and attach with two flathead screws.
7. Position trim plates on door in line with lock and attach using eight oval-head screws.
8. Insert spindle through hole A and attach knobs at each end of spindle.
9. Position strike in line with latch and attach with two flathead screws.
$81.99
