Logo



Logo
  • Products
    • Adapter Plates & Covers
    • Bolts, Latches & Guards
    • Door Reinforcers
    • Drawer, Cabinet & Mailbox Locks
    • Patio & Window Locks
    • Replacement Knobs & Rosettes
    • Strike Plates & Latch Guards
    • SecureShield
  • Smart Deadbolt
    • Product Information
    • FAQ
  • Security Facts
  • Contact Us
  • Cart
  • My Account

Double Cylinder Interlocking Deadbolt

    Home    Bolts, Latches & Guards    Double Cylinder Interlocking Deadbolt
1125

$46.99

SKU: 1125

Finish: Brass Tone

5-pin tumbler with hardened steel pins

Dual single or double cylinder locking unit & strike

Locks door to jamb to prevent forced
entry

Door Thickness: 1-3/8″ to 2-1/4″

1-1/4″ bore required

Includes tamper-resistant shutter guard

Key Blank: Weiser Blank WR2/WR3

Instructions:
CAUTIONS: Do not unscrew small retaining screws at rear of cylinder. Use only dry lubricant (graphite) on locks. Keep away clear of foreign objects.

To Install:
1. Select convenient  height for lock and place template against edge of door.
2. Mark hole positions. Bore 1-3/8″ hole for cylinder where indicated. Note: Bore through door until tip of drill barely emerges from other side. Remove drill bit and complete hole by drilling from opposite side to reduce splintering.
3. Drill 3/32″ diameter holes 1/2″ deep from attachment screws.
4. Insert cylinder and trim ring from outside of door. Attach backplate with two connecting bolts. Note: If bolts are too long, saw or break at groove, using caution to avoid marring the thread.
5. Cut or break connecting bar so it projects 3/8″ to 1/2″ beyond the inside of the door.
6. Plack lock on door so connecting bar enters “X” slot in back of lock. Secure with large mounting screws.
7. Align strike carefully, using template as a guide. Draw outline of strike on door jamb trim and chisel wood away (mortise) so strike mates freely with locking bars.
8. Mark mounting homes for strike, dill pilot holes, and secure strike to door jamb with screws provided.

Proposition 65 Warning

In stock

Add to Compare
SKU: 1125. Categories: All Categories, Bolts, Latches & Guards.
Related Products
STD A.S.A. Commercial Strike
All Categories

SKU: 1038

Finish: Stainless Steel

Use on wood or metal jambs

Works with most commercial Grade 1 lock sets

Dimensions: 1-1/4″ x 4-7/8″

Door Thickness: All

Instructions:
1. Remove old strike
2. Place strike on jamb, centered over latch hole.
3. Mark outline of strike on door jamb.
4. Using chisel, cut out area for strike 1/16″ deep.
5. Install screws.

 

Proposition 65 Warning


$8.09

Add to cart
Add to Compare
5-Pin Rim Cylinder
All Categories

SKU: 1150

Finish: Polished Brass

Zinc housing

5-pin tumbler lock

1-1/4″ bore hole required

Replacement lock cylinder for rim cylinder type lock sets

Key Blank: Weiser Blank WR5

Instructions:
1. Remove screws from old cylinder and remove cylinder.
2. Align connecting spindles of replacement cylinder to lock.
3. Insert screws into cylinder and tighten.


$10.39

Add to cart
Add to Compare
3″ Barrel Bolt
All Categories

SKU: 1853, 1853-SN

Finishes: Polished Brass & Satin Nickel

Includes keeper for surface mount

Easy to install

Instructions:
1. Position bolt plate on door at desired location and mark screw holes. Drill 3/32″ diameter pilot holes 1/2″ deep and fasten bolt plate to door with screws.
2. Position strike plate on door jamb over bolt, making sure bolt will slide into strike properly with bolt extended. mark screw hole locations. Drill 3/32″ diameter pilot holes 1/2″ deep and fasten strike plate to jamb with screws.


$11.99

Select options
Add to Compare
3″ Slide Bolt
All Categories

SKU: 1849, 1849-SN

Finishes: Polished Brass & Satin Nickel

For flush or recessed doors

Bolts surface mounts to face of door

2 keepers allow for surface or mortise frame installation

Instructions:
1. Position bolt at desired point on door and mark location of screws.
2. Close door and extend bolt. Mark position of bolt on door frame.
3. Use bolt mark on door frame fro strike placement. Two types of strikes are provided; use appropriate strike for door type, recessed or flush. Mark screw holes and fasten strike in place with screws.


$15.99

Select options
Add to Compare
Full Lip Strikes – 2 Pack
All Categories

SKU: 1063, 1064, 1065, 1065-SN, 1066

Finishes: Vintage Bronze, Antique Brass, Polished Brass, Satin Nickel & Chrome

Fits Standard size doors

Steel strike plate with adjustable tab

Replaces most residential exterior & interior strikes

Dimensions: 1-3/8″ x 2-1/4″

Door Thickness: All

Instructions:
1. Remove old strike.
2. Place new strike on door jamb, centered with latch hole.
3. Install screws provided and adjust tab with screw driver for proper fit.


$4.49 – $5.09

Select options
Add to Compare


About Us

First Watch Security, a division of Belwith Products, LLC. has been designing, manufacturing, and delivering home security products since 1959.

Today, First Watch Security is one of the most recognized brands in the market, producing products for home and commercial use.

Contact Us
  • +1.800.235.9484
  • 3100 Broadway Ave. SW Grandville, MI 49418
Connect With Us
  • Facebook
  • Twitter
  • Linkedin
Proposition 65 Warning

First Watch Security is an operating division of Belwith Products, LLC. | © 2015 Belwith Products, LLC. | All rights reserved.