Logo



Logo
  • Products
    • Adapter Plates & Covers
    • Bolts, Latches & Guards
    • Door Reinforcers
    • Drawer, Cabinet & Mailbox Locks
    • Patio & Window Locks
    • Replacement Knobs & Rosettes
    • Strike Plates & Latch Guards
    • SecureShield
  • Smart Deadbolt
    • Product Information
    • FAQ
  • Security Facts
  • Contact Us
  • Cart
  • My Account

Chain Door Guard

    Home    Bolts, Latches & Guards    Chain Door Guard
1862.

$10.19

SKU: 1862

Finish: Vintage Bronze

Secures door while allowing opening for
viewing or ventilation

Solid Brass material with steel chain

Easy to install

Instructions:
1. Mount long plate 1/4″ from edge of door at convenient height. Large hole at end of slot faces away from door jamb. Install 4 screws. (Drill 3/32″ pilot holes if necessary.)

2. Mount chain holder on door jamb so that knob on chain will reach hole in slide plate.

Proposition 65 Warning

In stock

Add to Compare
SKU: 1862. Categories: All Categories, Bolts, Latches & Guards.
Related Products
3″ Surface Bolt
All Categories

SKU:1848

Finish: Polished Brass

For flush or recessed doors

Bolt surface mounts to face of door

2 keepers allow for surface or mortise
frame installation

Guide brackets adjust fit unique
installation conditions


$8.59

Add to cart
Add to Compare
Adjustable Strike
All Categories

SKU: 1045

Finish: Polished  Brass

1/4″ adjustment for tight fit of door to frame

Stops door rattle

Assures engagement of dead latch function

Residential or commercial frames

Dimensions: 1-1/4″ x 2-3/4″

Door Thickness: All

Instructions:
Before starting first check door thickness for proper template alignment and then follow installation instructions.
-If door thickness is 1-3/4″ place template frame 3/16″ from door jamb.
-If door thickness is 1-3/8″ place template on the door jamb.

Installation Instructions:
1. Remove old strike.
2. Center template with latch hole and tape in place.
3. Position new strike in place and mark two holes. Chisel out area behind strike if needed or a flush fit is desired.
4. Drill 1/8″ pilot holes 2″ deep. Adjust to fit door.


$6.89

Add to cart
Add to Compare
Travel Lock
All Categories

SKU:1846

Finish: Chrome

Ideal for hotel/motel doors & drawers

Provides extra security to almost any
door

Locks & unlocks from inside with key

Uses door strike opening for mount point

Hook to catch strike plate on door or lip of cabinet

Instructions:
1. Using key, unlock travel lock and slide out locking bar.
2. Open door or drawer and hook locking bar into strike plate or onto inside lip of cabinet.
3. Close door or drawer and slide locking plate onto bar either horizontally or vertically as desired.
4. Slide lock onto locking bar tight against locking plate. Use key to lock and unlock.


$18.99

Add to cart
Add to Compare
Jumbo Door Viewer 180 Degrees
All Categories

SKU: 2330

Finish: Polished Brass

Material: Solid Brass

180 degree viewing area

Easy to install in 1-1/8″ hole

Door Thickness: 1-3/8″ to 2″

Instructions:
1. Mark door viewer location at eye level and centered horizontally on door.
2. Drill 1/8″ pilot hole completely through door.
3. Drill 1-1/8″ hole halfway through door from each side.
4. Install lens from outside.
5. Tighten inside retaining ring.


$43.99

Add to cart
Add to Compare
Double Cylinder Interlocking Deadbolt
All Categories

SKU: 1125

Finish: Brass Tone

5-pin tumbler with hardened steel pins

Dual single or double cylinder locking unit & strike

Locks door to jamb to prevent forced
entry

Door Thickness: 1-3/8″ to 2-1/4″

1-1/4″ bore required

Includes tamper-resistant shutter guard

Key Blank: Weiser Blank WR2/WR3

Instructions:
CAUTIONS: Do not unscrew small retaining screws at rear of cylinder. Use only dry lubricant (graphite) on locks. Keep away clear of foreign objects.

To Install:
1. Select convenient  height for lock and place template against edge of door.
2. Mark hole positions. Bore 1-3/8″ hole for cylinder where indicated. Note: Bore through door until tip of drill barely emerges from other side. Remove drill bit and complete hole by drilling from opposite side to reduce splintering.
3. Drill 3/32″ diameter holes 1/2″ deep from attachment screws.
4. Insert cylinder and trim ring from outside of door. Attach backplate with two connecting bolts. Note: If bolts are too long, saw or break at groove, using caution to avoid marring the thread.
5. Cut or break connecting bar so it projects 3/8″ to 1/2″ beyond the inside of the door.
6. Plack lock on door so connecting bar enters “X” slot in back of lock. Secure with large mounting screws.
7. Align strike carefully, using template as a guide. Draw outline of strike on door jamb trim and chisel wood away (mortise) so strike mates freely with locking bars.
8. Mark mounting homes for strike, dill pilot holes, and secure strike to door jamb with screws provided.


$46.99

Add to cart
Add to Compare


About Us

First Watch Security, a division of Belwith Products, LLC. has been designing, manufacturing, and delivering home security products since 1959.

Today, First Watch Security is one of the most recognized brands in the market, producing products for home and commercial use.

Contact Us
  • +1.800.235.9484
  • 3100 Broadway Ave. SW Grandville, MI 49418
Connect With Us
  • Facebook
  • Twitter
  • Linkedin
Proposition 65 Warning

First Watch Security is an operating division of Belwith Products, LLC. | © 2015 Belwith Products, LLC. | All rights reserved.