$14.39
SKU: 1143
Finish: Polished Brass
For old style passage locks
Dimensions: 2-1/2” diameter roses
Spindle size: 7mm
Fits up to 1-1/2″ diameter bore
Instructions:
1. Remove old hardware from door.
2. Attach new roses with screws provided.
3. Twist one knob onto spindle and slide through door hole while attaching to rose.
4. Twist last knob onto spindle and rose. Tighten knows using small screws on the side of knobs.
In stock
Add to Compare
SKU: 1148-PB, 1148-SN, 1148-VB
Finishes: Polished Brass, Satin Nickel & Vintage Bronze
Material: Steel
Glass Knobs
Latch is reversible to left or right handed door
Decorative passage latch for 2-3/8″
backset applications
Fits up to 1-1/2″ diameter bore
Dimensions: 2-1/2” diameter roses
Instructions:
1. Place square end of latch through 3/4″ hole in side of door. Install latch face by securing with wood screws. Note: If you find you have installed latch tongue in wrong direction for door jamb, grip sides of latch tongue with pliers, pull latch tongue out, turn to opposite side and let tongue snap back in place. Remove old strike plate. Install new strike plate into existing recess. Insert tow screws into face of strike plate and fasten securely. Tab may be adjusted forward with screwdriver to obtain firm latching.
2. Center rosettes over 3/4′ dia. hole and attach to door using 3/4″ wood screws provided. Place spindle through square drive in latch and thread knob onto spindle until they seat into rosettes. Back off 1/2 turn and tighten set screws onto spindle. Test for proper operation.
$15.89 – $20.39
SKU: 1139
Finish: Polished Brass
Glass knobs and trim plates
Case-hardened steel case
Bolt reversible to left and right handed door
Lock bolt is key activated both inside & outside
Requires mortise cutout
Replaces most bit key mortise locks with 2-1/4″ backset
Instructions:
1. Fold template (see insert included) along dotted line and wrap around inside edge of door at a convenient height. mark holes A and B through template.
2. Position vertical line C in center of door thickness and mark holes as shown. Be sure the template does not move up or down.
3. Remove template and drill seven 5/8″ diameter holes 3″ into edge of door where C holes were drawn. Chisel out remaining wood to form a pocket in the edge of the door measuring 5/8″ wide by 4-1/8″ long by 3″ deep.
4. Drill one 3/4″ hole on mark A through the door. Drill four 5/16″ holes as indicated through the door to form slot B.
5. Insert mortise lock into pocket, draw a line around the face plate, and remove lock. Chisel out the wood within the lines to a depth of approximately 3/32″. Insert lock occasionally to ensure proper depth.
6. Insert lock into door and attach with two flathead screws.
7. Position trim plates on door in line with lock and attach using eight oval-head screws.
8. Insert spindle through hole A and attach knobs at each end of spindle.
9. Position strike in line with latch and attach with two flathead screws.
$24.89
SKU: 1041, 1041-SN
Finish: Polished Brass, Solid Stainless Steel, Vintage Bronze, Chrome & Satin Nickel
Fits standard size doors
Use on wood or metal jambs
Common replacement for most Grade 2 & 3 locksets
Dimensions: 1-1/8″ x 2-3/4″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Place new strike on door jamb centered with latch hole.
3. Install screws provided and adjust tab with screw driver for proper fit.
$4.79
SKU: 1135
Finish: Polished Brass
Knob pair with spindle
Use on various interior mortise locksets
or latch sets
Spindle size: 7mm
$10.79
