SKU: 6001
Finish: Almond
Self adhesive & paintable
Repairs or prevents wall damage
$6.49
SKU: 5140
Finish: Chrome
For interior or exterior use
Rotating bolt to prevent sawing
Locks in closed or vented position
Non-removable screws
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$29.99
SKU: 3708-601
Finish: Chrome
Locks without key
Concealed screws
Rust resistant
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$20.89
SKU: 3708
Finish: Chrome
Locks without key
Concealed screws
Rust resistant
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$20.89
SKU: 2330
Finish: Polished Brass
Material: Solid Brass
180 degree viewing area
Easy to install in 1-1/8″ hole
Door Thickness: 1-3/8″ to 2″
Instructions:
1. Mark door viewer location at eye level and centered horizontally on door.
2. Drill 1/8″ pilot hole completely through door.
3. Drill 1-1/8″ hole halfway through door from each side.
4. Install lens from outside.
5. Tighten inside retaining ring.
$43.99
SKU:2258-PB, 2258-SS
Finishes: Stainless Steel & Polished Brass
Material: Solid Brass (PB only)
Strengthens and repairs damaged doors
Assists in preventing forced entry
Dimensions: 4-1/4″ x 9″
Backset: 2-3/4″
Door Thickness: 1-3/4″
Center to center: 5-1/2″
$46.49
SKU: 2051-SS, 2051-PB, 2051-SSS, 2051-VB
Finish: Stainless Steel, Polished Brass, Solid Stainless Steel & Vintage Bronze
Material: Solid Brass (SS, PB, VB) Solid Stainless Steel (SSS)
Strengthens and repairs damaged doors
Assists in preventing forced entry
Dimensions: 4″ x 4-1/2″
Backset: 2-3/8″
Door Thickness: 1-3/8″
Instructions:
1. Remove old lockset and latch screws (but not latch) and slide unit over door.
2. Push unit flush against edge of door. Replace latch screw with furnished long screws.
3. Drill pilot holes with 1/8″ bit 3/4″ deep and install 4 short mounting screws.
4. Install lockset.
Note: For tight fitting doors: If unit hits jamb when closing, remove and cut out 1/32″ on door edge so unit fits flush.
$10.61 – $21.99
SKU: 2001-SSS, 2001-VB
Finishes: Solid Stainless Steel & Vintage Bronze
Material: Solid Brass (VB) Solid Stainless Steel (SSS)
Strengthens and repairs damaged doors
Assists in preventing forced entry
Dimensions: 4″ x 9″
Backset: 2-3/8″
Door Thickness: 1-3/8″
Instructions:
1. Remove old lockset and latch screws, (but not latch) and slide unit over door.
2. Push unit flush against edge of door. Replace latch screw with furnished long screws.
3. Drill pilot holes with 1/8″ bit 3/4″ deep and install 4 shirt mounting screws.
4. Install lockset.
For tight fitting doors: If unit hits jamb when closing, remove and cut out 1/32″ on door edge so unit fits flush.
$43.99
SKU: 1978
Finish: Aluminum
Spring loaded, slide-in action securely locks door in closed or vented position.
Prevents lifting or sliding of door
Easy to install
$7.49
SKU: 1941
Finish: Aluminum
Cam action lock
Locks windows in closed or vented position
Instructions:
1. Place lock on track against window frame.
2. Press down on lever to lock.
3. For loose fitting doors, it may be necessary to place lock inside top track. Press on lever to lock.
$6.49
SKU: 1940
Finish: White
Cam action lock
Locks windows in closed or vented position
Instructions:
1. Place lock on track against window frame.
2. Press down on lever to lock.
3. For loose fitting doors, it may be necessary to place lock inside top track. Press on lever to lock.
$6.49
SKU: 1879
Finish: Polished Brass
Additional security of sliding dead bolt
Secures door while allowing opening for viewing or ventilation
Instructions:
1. Mount side place with sliding bolt inside on door at convenient height. Edge of slide place should be flush with door edge. Install four screws.
2. Mount strike place on door jamb so that sliding bolt engages the hole when door is fully closed. If door fit is tight, chisel out a recess on jamb for the strike plate. Install two screws.
3. Mount chain holder on jamb so that knob on chain will reach the hole in the slide plate when bolt is retracted. Mark and drill three pilot holes 3/32″ diameter and 1-1/4″ deep. Install chain holder with three screws.
$13.29
SKU: 1870, 1870-SN
Finishes: Satin Nickel & Polished Brass
Secures door while allowing opening for viewing or ventilation
Steel chain
Easy to install
Instructions:
1. Mount long plate 1/4″ from edge of door at convenient height. Large hole at end of slot faces away from door jamb. Install 4 screws. (Drill 3/32″ pilot holes if necessary.)
2. Mount chain holder on door jamb so that knob on chain will reach hole in slide plate
$8.79
SKU: 1853, 1853-SN
Finishes: Polished Brass & Satin Nickel
Includes keeper for surface mount
Easy to install
Instructions:
1. Position bolt plate on door at desired location and mark screw holes. Drill 3/32″ diameter pilot holes 1/2″ deep and fasten bolt plate to door with screws.
2. Position strike plate on door jamb over bolt, making sure bolt will slide into strike properly with bolt extended. mark screw hole locations. Drill 3/32″ diameter pilot holes 1/2″ deep and fasten strike plate to jamb with screws.
$11.99
SKU: 1849, 1849-SN
Finishes: Polished Brass & Satin Nickel
For flush or recessed doors
Bolts surface mounts to face of door
2 keepers allow for surface or mortise frame installation
Instructions:
1. Position bolt at desired point on door and mark location of screws.
2. Close door and extend bolt. Mark position of bolt on door frame.
3. Use bolt mark on door frame fro strike placement. Two types of strikes are provided; use appropriate strike for door type, recessed or flush. Mark screw holes and fasten strike in place with screws.
$15.99
SKU: 1847, 1847-SN
Finishes: Polished Brass & Satin Nickel
Material: Solid Brass
For flush or recessed doors
Bolt surface mounts to face of door
2 keepers allow for surface or mortise frame installation
Instructions:
1. Position bolt at desired point on door and mark location of screws.
2. Close door and extend bolt. Mark position of bolt on door frame.
3. Use bolt mark on door frame for strike placement. Two types of strikes are provided; use appropriate strike for door type, recessed or flush. Mark screw holes and fasten strike in place with screws.
$13.99
SKU: 1843
Finish: White
Locks or unlocks with flip action
No mortising required
Easy to install privacy lock
Instructions:
1. Position swing lock on the frame of the door at a convenient height. The lip should be curved towards the door frame.
2. Drill 3/32″ pilot holes 1/2″ deep and install large screws.
$4.49 – $4.59
SKU:1800
Finish: Polished Brass
Can be unlocked with key from inside or outside
Bolt slides into keyed mechanism to lock
Secures door while allowing 2″ opening or viewing or ventilation
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$18.99