Logo



Logo
  • Products
    • Adapter Plates & Covers
    • Bolts, Latches & Guards
    • Door Reinforcers
    • Drawer, Cabinet & Mailbox Locks
    • Patio & Window Locks
    • Replacement Knobs & Rosettes
    • Strike Plates & Latch Guards
    • SecureShield
  • Smart Deadbolt
    • Product Information
    • FAQ
  • Security Facts
  • Contact Us
  • Cart
  • My Account

Chain & Bolt Door Guard

    Home    Bolts, Latches & Guards    Chain & Bolt Door Guard
1879

$8.49

SKU: 1879

Finish: Polished Brass

Additional security of sliding dead bolt

Secures door while allowing opening for viewing or ventilation

 

Instructions:
1. Mount side place with sliding bolt inside on door at convenient height. Edge of slide place should be flush with door edge. Install four screws.
2. Mount strike place on door jamb so that sliding bolt engages the hole when door is fully closed. If door fit is tight, chisel out a recess on jamb for the strike plate. Install two screws.
3. Mount chain holder on jamb so that knob on chain will reach the hole in the slide plate when bolt is retracted. Mark and drill three pilot holes 3/32″ diameter and 1-1/4″ deep. Install chain holder with three screws.

Proposition 65 Warning

In stock

Add to Compare
SKU: 1879. Categories: All Categories, Bolts, Latches & Guards.
Related Products
Keyed Chain Door Guard
All Categories

SKU:1800

Finish: Polished Brass

Can be unlocked with key from inside or outside

Bolt slides into keyed mechanism to lock

Secures door while allowing 2″ opening or viewing or ventilation

Key Blank: Briggs & Stratton B1 & Yale Blank Y13


$11.29

Add to cart
Add to Compare
Single Cylinder Interlocking Deadbolt
All Categories

SKU: 1120

Finish: Polished Brass

5-pin tumbler with hardened steel pins

Single cylinder locking unit & strike

Locks door to jamb to prevent forced entry

1-1/4″ bore required

Includes tamper-resistant shutter guard

Door Thickness: 1-3/8″ to 2-1/4″

Key Blank: Weiser Blank WR2/WR3

Instructions:
CAUTION: Do not unscrew small retaining screws at rear of cylinder. Use only dry lubricant (graphite) on lock. Keep keyway clear of foreign objects.
1. Select convenient height for lock and place template against edge of door.
2. Mark hole positions. Bore 1-3/8″ hole for cylinder where indicated. Note: Bore through door until tip of drill barely emerges from other side. Remove drill bit and complete hole by drilling from opposite side to reduce splintering.
3. Drill 3/32″ diameter holes 1/2″ deep for attachment screws.
4. Insert cylinder and trim ring from outside of door. Attache backplate with two connecting bolts. Note: If bolts are too long, saw or break at groove, using caution to avoid marring the thread.
5. Cut or break connecting bar so it projects 3/8″ to 1/2″ beyond the inside of the door.
6. Plack lock on door so connecting bar enters “X” slot in back of lock. Secure with large mounting screws.
7. Align strike carefully, using template as a guide. Draw outline of strike on door jamb trim and chisel wood away (mortise) so strike mates freely with locking bars.
8. Mark mounting holes for strike, drill pilot holes, and secure strike to door jamb with screws provided.


$22.59

Add to cart
Add to Compare
Portable Swing Lock
All Categories

SKU: 1845

Finish: Polished Brass

Temporarily attaches to almost any door

Locks or unlocks with flip actions

Uses door strike opening for mount point


$2.49

Add to cart
Add to Compare


About Us

First Watch Security, a division of Belwith Products, LLC. has been designing, manufacturing, and delivering home security products since 1959.

Today, First Watch Security is one of the most recognized brands in the market, producing products for home and commercial use.

Contact Us
  • +1.800.235.9484
  • 3100 Broadway Ave. SW Grandville, MI 49418
Connect With Us
  • Facebook
  • Twitter
  • Linkedin
Proposition 65 Warning

First Watch Security is an operating division of Belwith Products, LLC. | © 2015 Belwith Products, LLC. | All rights reserved.