$92.99
SKU: 2001-SSS, 2001-VB
Finishes: Solid Stainless Steel & Vintage Bronze
Material: Solid Brass (VB) Solid Stainless Steel (SSS)
Strengthens and repairs damaged doors
Assists in preventing forced entry
Dimensions: 4″ x 9″
Backset: 2-3/8″
Door Thickness: 1-3/8″
Instructions:
1. Remove old lockset and latch screws, (but not latch) and slide unit over door.
2. Push unit flush against edge of door. Replace latch screw with furnished long screws.
3. Drill pilot holes with 1/8″ bit 3/4″ deep and install 4 shirt mounting screws.
4. Install lockset.
For tight fitting doors: If unit hits jamb when closing, remove and cut out 1/32″ on door edge so unit fits flush.
Proposition 65 Warning
SKU: 1120
Finish: Polished Brass
5-pin tumbler with hardened steel pins
Single cylinder locking unit & strike
Locks door to jamb to prevent forced entry
1-1/4″ bore required
Door Thickness: 1-3/8″ to 2-1/4″
Key Blank: Weiser Blank WR2/WR3
Instructions:
CAUTION: Do not unscrew small retaining screws at rear of cylinder. Use only dry lubricant (graphite) on lock. Keep keyway clear of foreign objects.
1. Select convenient height for lock and place template against edge of door.
2. Mark hole positions. Bore 1-3/8″ hole for cylinder where indicated. Note: Bore through door until tip of drill barely emerges from other side. Remove drill bit and complete hole by drilling from opposite side to reduce splintering.
3. Drill 3/32″ diameter holes 1/2″ deep for attachment screws.
4. Insert cylinder and trim ring from outside of door. Attache backplate with two connecting bolts. Note: If bolts are too long, saw or break at groove, using caution to avoid marring the thread.
5. Cut or break connecting bar so it projects 3/8″ to 1/2″ beyond the inside of the door.
6. Plack lock on door so connecting bar enters “X” slot in back of lock. Secure with large mounting screws.
7. Align strike carefully, using template as a guide. Draw outline of strike on door jamb trim and chisel wood away (mortise) so strike mates freely with locking bars.
8. Mark mounting holes for strike, drill pilot holes, and secure strike to door jamb with screws provided.
$51.99
SKU: 2051-SS, 2051-PB, 2051-SSS, 2051-VB
Finish: Stainless Steel, Polished Brass, Solid Stainless Steel & Vintage Bronze
Material: Solid Brass (SS, PB, VB) Solid Stainless Steel (SSS)
Strengthens and repairs damaged doors
Assists in preventing forced entry
Dimensions: 4″ x 4-1/2″
Backset: 2-3/8″
Door Thickness: 1-3/8″
Instructions:
1. Remove old lockset and latch screws (but not latch) and slide unit over door.
2. Push unit flush against edge of door. Replace latch screw with furnished long screws.
3. Drill pilot holes with 1/8″ bit 3/4″ deep and install 4 short mounting screws.
4. Install lockset.
Note: For tight fitting doors: If unit hits jamb when closing, remove and cut out 1/32″ on door edge so unit fits flush.
$39.99
SKU: 1089, 1089-SSS
Finishes: Polished Brass
Out-swinging doors only
Secures against forced entry
Protects latch or bolt
Residential or commercial use
Dimensions: 3″ x 7″
Backset: Locksets with 2-3/4″ backset
Instructions:
1. Place latch guard on door and center on lock.
2. Mark center of mounting holes.
3. Drill two 3/8″ holes through door.
4. Install bolts, washers and nuts. Tighten securely.
$26.99
SKU: 1090
Finish: Chrome
Out-swinging doors only
Secures against forced entry
Protects latch or bolt
Residential or commercial use
Dimensions: 3″ x 7″
Backset: Locksets with 2-3/4″ backset
Instructions:
1. Place latch guard on door and center on lock.
2. Mark center of mounting holes.
3. Drill two 3/8″ holes through door.
4. Install bolts, washer and nuts. Tighten securely.
Note: If latch guard contacts strike lip, bend in slightly with hammer.
$26.99
