$14.79 – $15.49
SKU: 2051-AB, 2051-PB, 2051-SSS, 2051-VB
Finish: Antique Brass, Polished Brass, Solid Stainless Steel & Vintage Bronze
Material: Solid Brass (AB, PB, VB) Solid Stainless Steel (SSS)
Strengthens and repairs damaged doors
Assists in preventing forced entry
Dimensions: 4″ x 4-1/2″
Backset: 2-3/8″
Door Thickness: 1-3/8″
Instructions:
1. Remove old lockset and latch screws (but not latch) and slide unit over door.
2. Push unit flush against edge of door. Replace latch screw with furnished long screws.
3. Drill pilot holes with 1/8″ bit 3/4″ deep and install 4 short mounting screws.
4. Install lockset.
Note: For tight fitting doors: If unit hits jamb when closing, remove and cut out 1/32″ on door edge so unit fits flush.
Proposition 65 Warning
SKU: 1085, 1085-SSS
Finishes: Polished Brass & Solid Stainless Steel
Out-swinging doors only
Secures against forced entry
Protects latch or bolt
Dimensions: 2-1/2″ x 6″
Backset: Locksets with 2-3/8″ backset
Instructions:
1. Place latch guard on door, center on lock.
2. Mark center of mounting holes.
3. Drill two 3/8″ holes through door.
4. Install bolts, washer, and nuts. Tighten securely.
Note: If latch guard contacts strike lip, bend in slightly with hammer.
$10.29 – $17.49
SKU: 1045
Finish: Polished Brass
1/4″ adjustment for tight fit of door to frame
Stops door rattle
Assures engagement of dead latch function
Residential or commercial frames
Dimensions: 1-1/4″ x 2-3/4″
Door Thickness: All
Instructions:
Before starting first check door thickness for proper template alignment and then follow installation instructions.
-If door thickness is 1-3/4″ place template frame 3/16″ from door jamb.
-If door thickness is 1-3/8″ place template on the door jamb.
Installation Instructions:
1. Remove old strike.
2. Center template with latch hole and tape in place.
3. Position new strike in place and mark two holes. Chisel out area behind strike if needed or a flush fit is desired.
4. Drill 1/8″ pilot holes 2″ deep. Adjust to fit door.
$3.69
SKU: 1105, 1105-SN
Finishes: Polished Brass & Satin Nickel
Latch hold-back (prevents locking yourself out)
5-pin tumbler with hardened steel pins
1-1/4″ bore required
Spring latch for automatic locking
Door Thickness: 1-3/8″ to 2-1/4″
Key Blank: Weiser Blank WR2/WR3
Instructions:
1. At desired height bore the hole for the cylinder 1-1/4″ diameter, with center at a distance of 2-3/8″ from edge of door.
2. Insert cylinder and ring from he outside of door and place back plate on inside of door. Connect back plate to cylinder with two connecting screws. Cut screws to proper length relative to door thickness.
3. Cut off connecting bar so that it projects 3/8″ beyond inside of door.
4. Plack lock on door so that connecting bar enters slot. Mark holes. Remove lock and drill 1/8″ pilot holes. Attache lock to door by inserting screws through lock into door.
5. Place strike plate on door jamb. Mark holes. Remove strike plate and drill 1/8″ pilot holes.
6. As needed, use chisel to cut door jamb so that strike is flush with door jamb.
$18.09 – $23.79
SKU: 1120
Finish: Polished Brass
5-pin tumbler with hardened steel pins
Single cylinder locking unit & strike
Locks door to jamb to prevent forced entry
1-1/4″ bore required
Includes tamper-resistant shutter guard
Door Thickness: 1-3/8″ to 2-1/4″
Key Blank: Weiser Blank WR2/WR3
Instructions:
CAUTION: Do not unscrew small retaining screws at rear of cylinder. Use only dry lubricant (graphite) on lock. Keep keyway clear of foreign objects.
1. Select convenient height for lock and place template against edge of door.
2. Mark hole positions. Bore 1-3/8″ hole for cylinder where indicated. Note: Bore through door until tip of drill barely emerges from other side. Remove drill bit and complete hole by drilling from opposite side to reduce splintering.
3. Drill 3/32″ diameter holes 1/2″ deep for attachment screws.
4. Insert cylinder and trim ring from outside of door. Attache backplate with two connecting bolts. Note: If bolts are too long, saw or break at groove, using caution to avoid marring the thread.
5. Cut or break connecting bar so it projects 3/8″ to 1/2″ beyond the inside of the door.
6. Plack lock on door so connecting bar enters “X” slot in back of lock. Secure with large mounting screws.
7. Align strike carefully, using template as a guide. Draw outline of strike on door jamb trim and chisel wood away (mortise) so strike mates freely with locking bars.
8. Mark mounting holes for strike, drill pilot holes, and secure strike to door jamb with screws provided.
$22.59
