SKU: 1879
Finish: Polished Brass
Additional security of sliding dead bolt
Secures door while allowing opening for viewing or ventilation
Instructions:
1. Mount side place with sliding bolt inside on door at convenient height. Edge of slide place should be flush with door edge. Install four screws.
2. Mount strike place on door jamb so that sliding bolt engages the hole when door is fully closed. If door fit is tight, chisel out a recess on jamb for the strike plate. Install two screws.
3. Mount chain holder on jamb so that knob on chain will reach the hole in the slide plate when bolt is retracted. Mark and drill three pilot holes 3/32″ diameter and 1-1/4″ deep. Install chain holder with three screws.
$8.49
SKU: 1870, 1870-SN
Finishes: Satin Nickel & Polished Brass
Secures door while allowing opening for viewing or ventilation
Steel chain
Easy to install
Instructions:
1. Mount long plate 1/4″ from edge of door at convenient height. Large hole at end of slot faces away from door jamb. Install 4 screws. (Drill 3/32″ pilot holes if necessary.)
2. Mount chain holder on door jamb so that knob on chain will reach hole in slide plate
$5.79
SKU: 1851, 1851-SN
Finishes: Polished Brass and Satin Nickel
Material: Solid Brass
For flush or recessed doors
Bolt surface mounts to face of door
2 keepers allow for surface or mortise frame installation
Instructions:
1. Position bolt at desired point on door and mark location of screws.
2. Close door and extend bolt. Mark position of bolt on door frame.
3. Use bolt mark on door frame for strike placement. Two types of strikes are provided; use appropriate strike for door type, recessed or flush. Mark screw holes and fasten strike in place with screws.
$9.29
SKU: 1849, 1849-SN
Finishes: Polished Brass & Satin Nickel
For flush or recessed doors
Bolts surface mounts to face of door
2 keepers allow for surface or mortise frame installation
Instructions:
1. Position bolt at desired point on door and mark location of screws.
2. Close door and extend bolt. Mark position of bolt on door frame.
3. Use bolt mark on door frame fro strike placement. Two types of strikes are provided; use appropriate strike for door type, recessed or flush. Mark screw holes and fasten strike in place with screws.
$7.99
SKU: 1847, 1847-SN
Finishes: Polished Brass & Satin Nickel
Material: Solid Brass
For flush or recessed doors
Bolt surface mounts to face of door
2 keepers allow for surface or mortise frame installation
Instructions:
1. Position bolt at desired point on door and mark location of screws.
2. Close door and extend bolt. Mark position of bolt on door frame.
3. Use bolt mark on door frame for strike placement. Two types of strikes are provided; use appropriate strike for door type, recessed or flush. Mark screw holes and fasten strike in place with screws.
$8.09
SKU: 1843
Finish: White
Locks or unlocks with flip action
No mortising required
Easy to install privacy lock
Instructions:
1. Position swing lock on the frame of the door at a convenient height. The lip should be curved towards the door frame.
2. Drill 3/32″ pilot holes 1/2″ deep and install large screws.
$2.79 – $2.89
SKU:1800
Finish: Polished Brass
Can be unlocked with key from inside or outside
Bolt slides into keyed mechanism to lock
Secures door while allowing 2″ opening or viewing or ventilation
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$11.29
SKU: 1430
Finish: Polished Brass
Mounts onto the edge of the upper window
Sliding stud stops opening at desired location
Flips away to allow window to open
Allows ventilation but prevents entry
Easy to install
Instructions:
1. Open window to desired height (not more than 4″ to 6″)
2. Position lock on inside edge of upper window as shown. Mark hole centers and drill small pilot holes. Install lock with screws provided.
3. Slide spring-loaded contact around to inside (closed) position.
4. Raise lower window (or lower upper window) observing where contact hits lower window frame. Mark center of that point. Install furnished strike plate.
$3.19
SKU: 1418
Finish: Polished Brass
Mounts on vertical track
Locks in closed or vented position
Flips away to allow window to open
Instructions:
1. Close window and attach lock 3″ to 4″ above top of lower sash with nails enclosed.
2. Swing stop closed to engage window stop, preventing window from being raised past window stop.
$3.09
SKU: 1407
Finish: Chrome
Mounts on vertical track
Locks in closed or vented position
Flips away to allow window to open
Instructions:
1. Close window and attach lock three to four inches above top of lower sash with nails enclosed.
2. Swing stop closed to engage window stop, preventing window from being raised past window stop.
$3.39
SKU: 1400-601
Finish: Polished Brass
For wood, aluminum, & vinyl double hung windows
Locks & unlocks with key
Cam action draws windows together to prevent drafts
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$10.09
SKU: 1381
Finish: Chrome
Keyed locking for maximum security
Requires 3/4″ mounting hole
For wood or metal door or drawer
2 washers for 90 or 180 degree rotation
Max drawer thickness 3/4″
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$6.79
SKU: 1358
Finish: Chrome
Keyed locking for maximum security
Requires 3/4″ mounting hole
For wood or metal door or drawer
2 washers for 90 or 180 degree rotation
Max drawer thickness 1/4″
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$6.49