$64.99
SKU: 1148-PB, 1148-SN, 1148-VB
Finishes: Polished Brass, Satin Nickel & Vintage Bronze
Material: Steel
Glass Knobs
Latch is reversible to left or right handed door
Decorative passage latch for 2-3/8″
backset applications
Fits up to 1-1/2″ diameter bore
Dimensions: 2-1/2” diameter roses
Instructions:
1. Place square end of latch through 3/4″ hole in side of door. Install latch face by securing with wood screws. Note: If you find you have installed latch tongue in wrong direction for door jamb, grip sides of latch tongue with pliers, pull latch tongue out, turn to opposite side and let tongue snap back in place. Remove old strike plate. Install new strike plate into existing recess. Insert tow screws into face of strike plate and fasten securely. Tab may be adjusted forward with screwdriver to obtain firm latching.
2. Center rosettes over 3/4′ dia. hole and attach to door using 3/4″ wood screws provided. Place spindle through square drive in latch and thread knob onto spindle until they seat into rosettes. Back off 1/2 turn and tighten set screws onto spindle. Test for proper operation.
SKU: 1063, 1064, 1065, 1065-SN, 1066
Finishes: Vintage Bronze, Antique Brass, Polished Brass, Satin Nickel & Chrome
Fits Standard size doors
Steel strike plate with adjustable tab
Replaces most residential exterior & interior strikes
Dimensions: 1-3/8″ x 2-1/4″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Place new strike on door jamb, centered with latch hole.
3. Install screws provided and adjust tab with screw driver for proper fit.
$9.99
SKU: 1041, 1041-SN
Finish: Polished Brass, Solid Stainless Steel, Vintage Bronze, Chrome & Satin Nickel
Fits standard size doors
Use on wood or metal jambs
Common replacement for most Grade 2 & 3 locksets
Dimensions: 1-1/8″ x 2-3/4″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Place new strike on door jamb centered with latch hole.
3. Install screws provided and adjust tab with screw driver for proper fit.
$9.99
SKU: 1045
Finish: Polished Brass
1/4″ adjustment for tight fit of door to frame
Stops door rattle
Assures engagement of dead latch function
Residential or commercial frames
Dimensions: 1-1/4″ x 2-3/4″
Door Thickness: All
Instructions:
Before starting first check door thickness for proper template alignment and then follow installation instructions.
-If door thickness is 1-3/4″ place template frame 3/16″ from door jamb.
-If door thickness is 1-3/8″ place template on the door jamb.
Installation Instructions:
1. Remove old strike.
2. Center template with latch hole and tape in place.
3. Position new strike in place and mark two holes. Chisel out area behind strike if needed or a flush fit is desired.
4. Drill 1/8″ pilot holes 2″ deep. Adjust to fit door.
$9.99
SKU: 1025, 1025-SSS, 1025-VB
Finishes: Polished Brass, Solid Stainless Steel & Vintage Bronze
Fits standard size doors
Strengthens or repairs wood jambs
3″ screws attach to wall stud for extra security
Dimensions: 1-1/4″ x 8″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Position new strike in place and mark the two mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or if a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install small screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike place and retest.
$17.99
