$64.99
SKU: 1148-PB, 1148-SN, 1148-VB
Finishes: Polished Brass, Satin Nickel & Vintage Bronze
Material: Steel
Glass Knobs
Latch is reversible to left or right handed door
Decorative passage latch for 2-3/8″
backset applications
Fits up to 1-1/2″ diameter bore
Dimensions: 2-1/2” diameter roses
Instructions:
1. Place square end of latch through 3/4″ hole in side of door. Install latch face by securing with wood screws. Note: If you find you have installed latch tongue in wrong direction for door jamb, grip sides of latch tongue with pliers, pull latch tongue out, turn to opposite side and let tongue snap back in place. Remove old strike plate. Install new strike plate into existing recess. Insert tow screws into face of strike plate and fasten securely. Tab may be adjusted forward with screwdriver to obtain firm latching.
2. Center rosettes over 3/4′ dia. hole and attach to door using 3/4″ wood screws provided. Place spindle through square drive in latch and thread knob onto spindle until they seat into rosettes. Back off 1/2 turn and tighten set screws onto spindle. Test for proper operation.
SKU: 1085, 1085-SSS
Finishes: Polished Brass & Solid Stainless Steel
Out-swinging doors only
Secures against forced entry
Protects latch or bolt
Dimensions: 2-1/2″ x 6″
Backset: Locksets with 2-3/8″ backset
Instructions:
1. Place latch guard on door, center on lock.
2. Mark center of mounting holes.
3. Drill two 3/8″ holes through door.
4. Install bolts, washer, and nuts. Tighten securely.
Note: If latch guard contacts strike lip, bend in slightly with hammer.
$22.99
SKU: 1146
Finish: White
For old style passage locks
Screw mounted on door
Dimensions: 2-1/2” diameter
Fits up to 1-1/2″ diameter bore
Instructions:
1. Remove door knob and old roses.
2. Replace with new roses by lining up the holes and attaching screws. Attach door knobs.
$3.99
SKU: 1025, 1025-SSS, 1025-VB
Finishes: Polished Brass, Solid Stainless Steel & Vintage Bronze
Fits standard size doors
Strengthens or repairs wood jambs
3″ screws attach to wall stud for extra security
Dimensions: 1-1/4″ x 8″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Position new strike in place and mark the two mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or if a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install small screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike place and retest.
$17.99
SKU: 1089, 1089-SSS
Finishes: Polished Brass
Out-swinging doors only
Secures against forced entry
Protects latch or bolt
Residential or commercial use
Dimensions: 3″ x 7″
Backset: Locksets with 2-3/4″ backset
Instructions:
1. Place latch guard on door and center on lock.
2. Mark center of mounting holes.
3. Drill two 3/8″ holes through door.
4. Install bolts, washers and nuts. Tighten securely.
$26.99
SKU: 1005
Finish: Polished Brass
Fits standard size doors
Mortising required
Screws at base of box strike secure to
2″ x 4″ framing for added security
Dimensions: 1-1/4″ x 4-7/8″
Door Thickness: All
Instructions:
1. Mark center of bolt on frame.
2. Cut out template (see insert), locate center mark on template with center mark on frame. Tape in place.
3. Draw around outside of template. Mark 4 holes through template. Drill 1″ holes per template.
4. Chisel out between 1″ holes and fit strike box.
5. Chisel out 1/8″ deep for strike.
6. Install strike and faceplate with top and bottom screws. (Be sure 2 holes in strike box are toward center of frame.)
7. Drill two 1/8″ pilot holes at bottom of strike box toward center of frame and install screws at an angle.
$12.99
