$22.99
SKU: 1155
Finish: Polished Brass
Mortise lock with faceplate
Case-hardened steel case
Replaces most bit key mortise locks with 2-1/4″ backset
Bolt reversible to left and right handed door
Requires mortise cutout
Instructions:
1. Remove old lock and strike plate.
2. Position new lock into hole and pound in with hammer. Make sure deadbolt is on the bottom.
3. Attache with screws provided.
4. Align strike plate with existing holes and attach with screws provided.
SKU: 1038
Finish: Stainless Steel
Use on wood or metal jambs
Works with most commercial Grade 1 lock sets
Dimensions: 1-1/4″ x 4-7/8″
Door Thickness: All
Instructions:
1. Remove old strike
2. Place strike on jamb, centered over latch hole.
3. Mark outline of strike on door jamb.
4. Using chisel, cut out area for strike 1/16″ deep.
5. Install screws.
$8.09
SKU: 1143
Finish: Polished Brass
For old style passage locks
Dimensions: 2-1/2” diameter roses
Spindle size: 7mm
Fits up to 1-1/2″ diameter bore
Instructions:
1. Remove old hardware from door.
2. Attach new roses with screws provided.
3. Twist one knob onto spindle and slide through door hole while attaching to rose.
4. Twist last knob onto spindle and rose. Tighten knows using small screws on the side of knobs.
$27.99
SKU: 1041, 1041-SN
Finish: Polished Brass, Solid Stainless Steel, Vintage Bronze, Chrome & Satin Nickel
Fits standard size doors
Use on wood or metal jambs
Common replacement for most Grade 2 & 3 locksets
Dimensions: 1-1/8″ x 2-3/4″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Place new strike on door jamb centered with latch hole.
3. Install screws provided and adjust tab with screw driver for proper fit.
$6.89
SKU:1129
Finish: Polished Brass
Knobs and trim plates
Case-hardened steel case
Lock bolt is key activated both inside & outside
Bolt reversible to left and right handed door
Requires mortise cutout
Replaces most bit key mortise locks with 2-1/4″ backset
Instructions:
1. Fold template (see insert included) along dotted line and wrap around inside edge of door at a convenient height. mark holes A and B through template.
2. Position vertical line C in center of door thickness and mark holes as shown. Be sure the template does not move up or down.
3. Remove template and drill seven 5/8″ diameter holes 3″ into edge of door where C holes were drawn. Chisel out remaining wood to form a pocket in the edge of the door measuring 5/8″ wide by 4-1/8″ long by 3″ deep.
4. Drill one 3/4″ hole on mark A through the door. Drill four 5/16″ holes as indicated through the door to form slot B.
5. Insert mortise lock into pocket, draw a line around the face plate, and remove lock. Chisel out the wood within the lines to a depth of approximately 3/32″. Insert lock occasionally to ensure proper depth.
6. Insert lock into door and attach with two flathead screws.
7. Position trim plates on door in line with lock and attach using eight oval-head screws.
8. Insert spindle through hole A and attach knobs at each end of spindle.
9. Position strike in line with latch and attach with two flathead screws.
$41.99
SKU: 1139
Finish: Polished Brass
Glass knobs and trim plates
Case-hardened steel case
Bolt reversible to left and right handed door
Lock bolt is key activated both inside & outside
Requires mortise cutout
Replaces most bit key mortise locks with 2-1/4″ backset
Instructions:
1. Fold template (see insert included) along dotted line and wrap around inside edge of door at a convenient height. mark holes A and B through template.
2. Position vertical line C in center of door thickness and mark holes as shown. Be sure the template does not move up or down.
3. Remove template and drill seven 5/8″ diameter holes 3″ into edge of door where C holes were drawn. Chisel out remaining wood to form a pocket in the edge of the door measuring 5/8″ wide by 4-1/8″ long by 3″ deep.
4. Drill one 3/4″ hole on mark A through the door. Drill four 5/16″ holes as indicated through the door to form slot B.
5. Insert mortise lock into pocket, draw a line around the face plate, and remove lock. Chisel out the wood within the lines to a depth of approximately 3/32″. Insert lock occasionally to ensure proper depth.
6. Insert lock into door and attach with two flathead screws.
7. Position trim plates on door in line with lock and attach using eight oval-head screws.
8. Insert spindle through hole A and attach knobs at each end of spindle.
9. Position strike in line with latch and attach with two flathead screws.
$39.99
