$35.99
SKU: 1155
Finish: Polished Brass
Mortise lock with faceplate
Case-hardened steel case
Replaces most bit key mortise locks with 2-1/4″ backset
Bolt reversible to left and right handed door
Requires mortise cutout
Instructions:
1. Remove old lock and strike plate.
2. Position new lock into hole and pound in with hammer. Make sure deadbolt is on the bottom.
3. Attache with screws provided.
4. Align strike plate with existing holes and attach with screws provided.
SKU: 1038
Finish: Stainless Steel
Use on wood or metal jambs
Works with most commercial Grade 1 lock sets
Dimensions: 1-1/4″ x 4-7/8″
Door Thickness: All
Instructions:
1. Remove old strike
2. Place strike on jamb, centered over latch hole.
3. Mark outline of strike on door jamb.
4. Using chisel, cut out area for strike 1/16″ deep.
5. Install screws.
$21.99
SKU: 1085, 1085-SSS
Finishes: Polished Brass & Solid Stainless Steel
Out-swinging doors only
Secures against forced entry
Protects latch or bolt
Dimensions: 2-1/2″ x 6″
Backset: Locksets with 2-3/8″ backset
Instructions:
1. Place latch guard on door, center on lock.
2. Mark center of mounting holes.
3. Drill two 3/8″ holes through door.
4. Install bolts, washer, and nuts. Tighten securely.
Note: If latch guard contacts strike lip, bend in slightly with hammer.
$22.99
SKU: 1027
Finish: Polished Brass
For locks with 5-1/2″ to 6″ centers
Replaces standard latch & deadbolt
strikes with one piece security
Strengthens or repairs wood jambs
3″ screws attach to wall stud for extra security
Dimensions: 1-5/8″ x 11″
Door Thickness: 1-3/4″ or thicker doors
Instructions:
1. Remove old strike
2. Position new strike in place and mark with a pencil the three mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install short screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike plate and retest.
Note: Check distance between door and frame when door is closed.
– If the gap is 1/4″ or more install strike on surface of frame.
– If the gap is less than a 1/4″ strike must be chiseled into the frame.
$22.99
SKU: 1141, 1141-SN
Finishes: Satin Nickel & Polished Brass
Material: Solid Brass
For old style passage locks
Screw mounted on door
Dimensions: 2-1/2″ diameter
Fits up to 1-1/2″ diameter bore
Instructions:
1. Remove door knob and old roses.
2. Replace with new roses by lining up the holes and attaching screws. Attach door knobs.
$16.99
SKU: 1005
Finish: Polished Brass
Fits standard size doors
Mortising required
Screws at base of box strike secure to
2″ x 4″ framing for added security
Dimensions: 1-1/4″ x 4-7/8″
Door Thickness: All
Instructions:
1. Mark center of bolt on frame.
2. Cut out template (see insert), locate center mark on template with center mark on frame. Tape in place.
3. Draw around outside of template. Mark 4 holes through template. Drill 1″ holes per template.
4. Chisel out between 1″ holes and fit strike box.
5. Chisel out 1/8″ deep for strike.
6. Install strike and faceplate with top and bottom screws. (Be sure 2 holes in strike box are toward center of frame.)
7. Drill two 1/8″ pilot holes at bottom of strike box toward center of frame and install screws at an angle.
$12.99
