SKU: 1862
Finish: Vintage Bronze
Secures door while allowing opening for
viewing or ventilation
Solid Brass material with steel chain
Easy to install
Instructions:
1. Mount long plate 1/4″ from edge of door at convenient height. Large hole at end of slot faces away from door jamb. Install 4 screws. (Drill 3/32″ pilot holes if necessary.)
2. Mount chain holder on door jamb so that knob on chain will reach hole in slide plate.
$7.89
SKU: 2038-PB
Finishes: Polished Brass
Material: Solid Brass
Strengthens and repairs damaged doors
Assists in preventing forced entry
Dimensions: 3” x 4-1/4”
Backset: 2-3/4”
Door Thickness: 1-3/4”
$12.39
SKU: 2020-PB, 2020-VB
Finishes: Polished Brass
Repairs damaged doors
Assists in preventing forced entry
Dimensions: 1” x 4-1/2”
Door Thickness: 1-3/4”
$8.29
SKU: 2320, 2321, 2322
Finishes: Polished Brass, Chrome, Vintage Bronze
Material: Solid Brass
190 degree viewing area
Easy to install in 1/2″ hole
Door Thickness: 1-3/8″ to 2″
Instructions:
1. Mark door viewer location at eye level and centered horizontally on door.
2. Drill 1/8″ pilot hole completely through door.
3. Drill 1-1/8″ hole halfway through door from each side.
4. Install lens from outside.
5. Tighten inside retaining ring.
$12.49
SKU: 2051-AB, 2051-PB, 2051-SSS, 2051-VB
Finish: Antique Brass, Polished Brass, Solid Stainless Steel & Vintage Bronze
Material: Solid Brass (AB, PB, VB) Solid Stainless Steel (SSS)
Strengthens and repairs damaged doors
Assists in preventing forced entry
Dimensions: 4″ x 4-1/2″
Backset: 2-3/8″
Door Thickness: 1-3/8″
Instructions:
1. Remove old lockset and latch screws (but not latch) and slide unit over door.
2. Push unit flush against edge of door. Replace latch screw with furnished long screws.
3. Drill pilot holes with 1/8″ bit 3/4″ deep and install 4 short mounting screws.
4. Install lockset.
Note: For tight fitting doors: If unit hits jamb when closing, remove and cut out 1/32″ on door edge so unit fits flush.
$14.79 – $15.49
SKU: 2001-SSS, 2001-VB
Finishes: Solid Stainless Steel & Vintage Bronze
Material: Solid Brass (VB) Solid Stainless Steel (SSS)
Strengthens and repairs damaged doors
Assists in preventing forced entry
Dimensions: 4″ x 9″
Backset: 2-3/8″
Door Thickness: 1-3/8″
Instructions:
1. Remove old lockset and latch screws, (but not latch) and slide unit over door.
2. Push unit flush against edge of door. Replace latch screw with furnished long screws.
3. Drill pilot holes with 1/8″ bit 3/4″ deep and install 4 shirt mounting screws.
4. Install lockset.
For tight fitting doors: If unit hits jamb when closing, remove and cut out 1/32″ on door edge so unit fits flush.
$30.89
SKU: 1385
Finishes: Stainless Steel & Vintage Bronze
Keyed locking for maximum security
Requires 3/4″ mounting hole
For wood or metal door or drawer
2 washers for 90 or 180 degree rotation
Max drawer thickness 3/4″
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$6.69 – $10.59
SKU: 1172, 1172-SN, 1172-VB, 1172-W
Finishes: Polished Brass, Satin Nickel, Vintage Bronze & White
Helps maintain entry security
Covers lockset holes from 1/2″ to 2-1/8″
Fits doors to 1-3/4″ thick
Dimensions: 2-5/8″ diameter
Instructions:
1. Place door plate with cylinder extending into door hole.
2. Place other plate on opposite side of door with indentation facing door hole.
3. Insert screw through plate into cylinder and tighten.
$5.09 – $5.69
SKU: 1148-PB, 1148-SN, 1148-VB
Finishes: Polished Brass, Satin Nickel & Vintage Bronze
Material: Steel
Glass Knobs
Latch is reversible to left or right handed door
Decorative passage latch for 2-3/8″
backset applications
Fits up to 1-1/2″ diameter bore
Dimensions: 2-1/2” diameter roses
Instructions:
1. Place square end of latch through 3/4″ hole in side of door. Install latch face by securing with wood screws. Note: If you find you have installed latch tongue in wrong direction for door jamb, grip sides of latch tongue with pliers, pull latch tongue out, turn to opposite side and let tongue snap back in place. Remove old strike plate. Install new strike plate into existing recess. Insert tow screws into face of strike plate and fasten securely. Tab may be adjusted forward with screwdriver to obtain firm latching.
2. Center rosettes over 3/4′ dia. hole and attach to door using 3/4″ wood screws provided. Place spindle through square drive in latch and thread knob onto spindle until they seat into rosettes. Back off 1/2 turn and tighten set screws onto spindle. Test for proper operation.
$15.89 – $20.39
SKU: 1063, 1064, 1065, 1065-SN, 1066
Finishes: Vintage Bronze, Antique Brass, Polished Brass, Satin Nickel & Chrome
Fits Standard size doors
Steel strike plate with adjustable tab
Replaces most residential exterior & interior strikes
Dimensions: 1-3/8″ x 2-1/4″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Place new strike on door jamb, centered with latch hole.
3. Install screws provided and adjust tab with screw driver for proper fit.
$3.49 – $5.19
SKU: 1025, 1025-SSS, 1025-VB
Finishes: Polished Brass, Solid Stainless Steel & Vintage Bronze
Fits standard size doors
Strengthens or repairs wood jambs
3″ screws attach to wall stud for extra security
Dimensions: 1-1/4″ x 8″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Position new strike in place and mark the two mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or if a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install small screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike place and retest.
$7.89 – $11.29