SKU: 1847, 1847-SN
Finishes: Polished Brass & Satin Nickel
Material: Solid Brass
For flush or recessed doors
Bolt surface mounts to face of door
2 keepers allow for surface or mortise frame installation
Instructions:
1. Position bolt at desired point on door and mark location of screws.
2. Close door and extend bolt. Mark position of bolt on door frame.
3. Use bolt mark on door frame for strike placement. Two types of strikes are provided; use appropriate strike for door type, recessed or flush. Mark screw holes and fasten strike in place with screws.
$13.99
SKU: 1843
Finish: White
Locks or unlocks with flip action
No mortising required
Easy to install privacy lock
Instructions:
1. Position swing lock on the frame of the door at a convenient height. The lip should be curved towards the door frame.
2. Drill 3/32″ pilot holes 1/2″ deep and install large screws.
$4.49 – $4.59
SKU: 1409
Finish: Aluminum
Locks window in closed or vented position
For use on sliding windows
Extruded aluminum with steel thumbscrew
Instructions:
To Lock:
1. Close window securely.
2. Plack lock against edge of sliding window on bottom track and tighten thumb screw.
To Vent:
1. Open sliding window 1-1/2″ to 2″. Place lock against edge of sliding window on bottom track and tighten thumb screw.
$5.29
SKU: 1408
Finish: Aluminum
Extruded aluminum with no-mar vinyl inserts to protect track
Locks window in closed or vented position
Fits wide & narrow type tracks
For use on sliding windows
Instructions:
To Lock:
1. Close window securely.
2. Placke lock against edge of sliding window on bottom track and turn wing clockwise until wedge is tight.
To Vent:
1. Open sliding window 1-1/2″ to 2″. Place lock against edge of sliding window on bottom track and turn wing nut clockwise until wedge is tight.
$5.99
SKU: 1407
Finish: Chrome
Mounts on vertical track
Locks in closed or vented position
Flips away to allow window to open
Instructions:
1. Close window and attach lock three to four inches above top of lower sash with nails enclosed.
2. Swing stop closed to engage window stop, preventing window from being raised past window stop.
$5.79
SKU: 1385
Finishes: Stainless Steel & Vintage Bronze
Keyed locking for maximum security
Requires 3/4″ mounting hole
For wood or metal door or drawer
2 washers for 90 or 180 degree rotation
Max drawer thickness 3/4″
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$12.89 – $13.99
SKU: 1381
Finish: Chrome
Keyed locking for maximum security
Requires 3/4″ mounting hole
For wood or metal door or drawer
2 washers for 90 or 180 degree rotation
Max drawer thickness 3/4″
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$9.19
SKU: 1358
Finish: Chrome
Keyed locking for maximum security
Requires 3/4″ mounting hole
For wood or metal door or drawer
2 washers for 90 or 180 degree rotation
Max drawer thickness 1/4″
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$8.09
SKU: 1356, 1356-VB
Finishes: Polished Brass & Vintage Bronze
Requires 7/8″ mounting hole
Max cabinet or drawer thickness 1-1/8″
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
Instructions:
1. Drill 7/8″ diameter hole for lock if necessary.
2. Push lock through hole form inside of drawer. Use lock for template to mark screw holes.
3. Drill small pilot holes 1/2″ deep and screw lock into position.
$10.49
SKU: 1355, 1355-VB
Finishes: Polished Brass & Vintage Bronze
Requires 7/8″ mounting hole
Max cabinet or drawer thickness 3/4″
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$10.49
SKU: 1275
Finish: Aluminum
For sliding door opening 28″- 52″
Telescoping aluminum locking bar
No cutting needed
Easy installation
Instructions:
To install inside sliding door:
1. Place rotating bracket on wall next to stationary door.
2. Mark and drill 1/8″ diameter holes and attach bracket to wall with screws provided.
3. With other end of bar in locking saddle, extend bar to inside edge of sliding door. Hold in horizontal position and mark and drill 1/8″ holes. Install screws through saddle catch into door.
To install outside sliding door:
1. Install jamb and bracket against inside edge of non-moving door.
2. Locking saddle install on inside frame of moveable door. Caution: Care must be taken that locking saddle is positioned at least 2″ above the sliding door handle.
$14.29
SKU: 1253
Finish: Aluminum Tone
Securely locks in closed or vented position
Assembled with hardened steel bolt
Easily activated with foot
Locks and unlocks with key
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
Instructions:
CAUTION: Before installation, check with patio door manufacturer for door specifications. Failure to do so may result in glass breakage!
1. Close sliding door completely.
2. With bolt retracted, place lock in desired position at top or bottom of leading edge of sliding door, leaving enough room to clear track so door slides smoothly.
3. Tap back of lock lightly with hammer to mark bolt hole position; remove lock. Make sure drill will clear glass. Drill 1-1/32″ diameter hole for locking bolt.
4. With bolt extended, position lock and slide bolt into hole. mark screw holes, remove lock and drill 1/8″ diameter holes.
5. Replace lock; install with standard screws and tighten. Or, to make door tamper-proof, remove standard screws and replace with non-removable screws.
$13.79
SKU: 1191
Finish: Prime Coat Gray
Covers unused latch face cutouts
Dimensions: 2.25″ x 1.10″
Instructions:
1. Insert filler plate into door edge.
2. Install screws.
$3.49
SKU: 1173
Finish: Prime Coat Gray
Helps maintain entry security
Covers lockset holes from 1/2″ to 2-1/8″
Fits doors to 1-3/4″ thick
Dimensions: 2-5/8″ diameter
Instructions:
1. Place door plate with cylinder extending into door hole.
2. Place other plate on opposite side of door with indentation facing door hole.
3. Insert screw through plate into cylinder and tighten.
$6.89
SKU: 1172, 1172-SN, 1172-VB
Finishes: Polished Brass, Satin Nickel and Vintage Bronze
Helps maintain entry security
Covers lockset holes from 1/2″ to 2-1/8″
Fits doors to 1-3/4″ thick
Dimensions: 2-5/8″ diameter
Instructions:
1. Place door plate with cylinder extending into door hole.
2. Place other plate on opposite side of door with indentation facing door hole.
3. Insert screw through plate into cylinder and tighten.
$8.29
SKU: 1170, 1170-SN, 1170-SSS,
Finishes: Polished Brass, Satin Nickel, Solid Stainless Steel
Material: Solid Stainless Steel (SSS only)
Use with 2-1/8″ bore locks
Covers marred area around knob
Allows conversion of 2-3/8″ to 2-3/4″ backset
Dimensions: 3-1/2″ diameter
Instructions:
1. Remove lockset.
2. Place trim against door and reinstall lockset.
$6.39 – $9.39
SKU: 1165, 1165-SN
Finishes: Polished Brass and Satin Nickel
Reduces bore from 2-1/8″ to 1-1/2″
For use with some deadbolts and rim cylinders
Instructions:
1. Remove deadbolt from door.
2. Install trim against door and them reinstall deadbolt.
$7.29 – $9.19
SKU: 1148-PB, 1148-SN, 1148-VB
Finishes: Polished Brass, Satin Nickel & Vintage Bronze
Material: Steel
Glass Knobs
Latch is reversible to left or right handed door
Decorative passage latch for 2-3/8″
backset applications
Fits up to 1-1/2″ diameter bore
Dimensions: 2-1/2” diameter roses
Instructions:
1. Place square end of latch through 3/4″ hole in side of door. Install latch face by securing with wood screws. Note: If you find you have installed latch tongue in wrong direction for door jamb, grip sides of latch tongue with pliers, pull latch tongue out, turn to opposite side and let tongue snap back in place. Remove old strike plate. Install new strike plate into existing recess. Insert tow screws into face of strike plate and fasten securely. Tab may be adjusted forward with screwdriver to obtain firm latching.
2. Center rosettes over 3/4′ dia. hole and attach to door using 3/4″ wood screws provided. Place spindle through square drive in latch and thread knob onto spindle until they seat into rosettes. Back off 1/2 turn and tighten set screws onto spindle. Test for proper operation.
$38.99