SKU: 1430
Finish: Polished Brass
Mounts onto the edge of the upper window
Sliding stud stops opening at desired location
Flips away to allow window to open
Allows ventilation but prevents entry
Easy to install
Instructions:
1. Open window to desired height (not more than 4″ to 6″)
2. Position lock on inside edge of upper window as shown. Mark hole centers and drill small pilot holes. Install lock with screws provided.
3. Slide spring-loaded contact around to inside (closed) position.
4. Raise lower window (or lower upper window) observing where contact hits lower window frame. Mark center of that point. Install furnished strike plate.
$7.99
SKU: 1425
Finish: Gray
Locks in closed or vented position
Locks & unlocks with key
Comes with 2 inserts (not shown)
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$15.69
SKU: 1418
Finish: Polished Brass
Mounts on vertical track
Locks in closed or vented position
Flips away to allow window to open
Instructions:
1. Close window and attach lock 3″ to 4″ above top of lower sash with nails enclosed.
2. Swing stop closed to engage window stop, preventing window from being raised past window stop.
$5.79
SKU: 1411
Finish: White
Comes in pack of two
Locks window in closed or vented position
For use on sliding windows
Extruded aluminum with steel thumbscrew
Instructions:
To Lock:
1. Close window securely.
2. Plack lock against edge of sliding window on bottom track and tighten thumb screw.
To Vent:
1. Open sliding window 1-1/2″ to 2″. Place lock against edge of sliding window on bottom track and tighten thumb screw.
$5.79
SKU: 1409
Finish: Aluminum
Locks window in closed or vented position
For use on sliding windows
Extruded aluminum with steel thumbscrew
Instructions:
To Lock:
1. Close window securely.
2. Plack lock against edge of sliding window on bottom track and tighten thumb screw.
To Vent:
1. Open sliding window 1-1/2″ to 2″. Place lock against edge of sliding window on bottom track and tighten thumb screw.
$5.29
SKU: 1408
Finish: Aluminum
Extruded aluminum with no-mar vinyl inserts to protect track
Locks window in closed or vented position
Fits wide & narrow type tracks
For use on sliding windows
Instructions:
To Lock:
1. Close window securely.
2. Placke lock against edge of sliding window on bottom track and turn wing clockwise until wedge is tight.
To Vent:
1. Open sliding window 1-1/2″ to 2″. Place lock against edge of sliding window on bottom track and turn wing nut clockwise until wedge is tight.
$5.99
SKU: 1407
Finish: Chrome
Mounts on vertical track
Locks in closed or vented position
Flips away to allow window to open
Instructions:
1. Close window and attach lock three to four inches above top of lower sash with nails enclosed.
2. Swing stop closed to engage window stop, preventing window from being raised past window stop.
$5.79
SKU: 1404
Finish: White
For wood, aluminum, & vinyl double hung windows
Locks & unlocks with key
Cam action draws windows together to prevent drafts
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$13.99
SKU: 1400-601
Finish: Polished Brass
For wood, aluminum, & vinyl double hung windows
Locks & unlocks with key
Cam action draws windows together to prevent drafts
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$10.09
SKU: 1276
Finish: White
For sliding door opening 28″- 52″
Telescoping aluminum locking bar
No cutting needed
Easy installation
Instructions:
To install inside sliding door:
1. Place rotating bracket on wall next to stationary door.
2. Mark and drill 1/8″ diameter holes and attach bracket to wall with screws provided.
3. With other end of bar in locking saddle, extend bar to inside edge of sliding door. Hold in horizontal position and mark and drill 1/8″ holes. Install screws through saddle catch into door.
To install outside sliding door:
1. Install jamb and bracket against inside edge of non-moving door.
2. Locking saddle install on inside frame of moveable door. Caution: Care must be taken that locking saddle is positioned at least 2″ above the sliding door handle.
$17.79
SKU: 1275
Finish: Aluminum
For sliding door opening 28″- 52″
Telescoping aluminum locking bar
No cutting needed
Easy installation
Instructions:
To install inside sliding door:
1. Place rotating bracket on wall next to stationary door.
2. Mark and drill 1/8″ diameter holes and attach bracket to wall with screws provided.
3. With other end of bar in locking saddle, extend bar to inside edge of sliding door. Hold in horizontal position and mark and drill 1/8″ holes. Install screws through saddle catch into door.
To install outside sliding door:
1. Install jamb and bracket against inside edge of non-moving door.
2. Locking saddle install on inside frame of moveable door. Caution: Care must be taken that locking saddle is positioned at least 2″ above the sliding door handle.
$14.29
SKU: 1253
Finish: Aluminum Tone
Securely locks in closed or vented position
Assembled with hardened steel bolt
Easily activated with foot
Locks and unlocks with key
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
Instructions:
CAUTION: Before installation, check with patio door manufacturer for door specifications. Failure to do so may result in glass breakage!
1. Close sliding door completely.
2. With bolt retracted, place lock in desired position at top or bottom of leading edge of sliding door, leaving enough room to clear track so door slides smoothly.
3. Tap back of lock lightly with hammer to mark bolt hole position; remove lock. Make sure drill will clear glass. Drill 1-1/32″ diameter hole for locking bolt.
4. With bolt extended, position lock and slide bolt into hole. mark screw holes, remove lock and drill 1/8″ diameter holes.
5. Replace lock; install with standard screws and tighten. Or, to make door tamper-proof, remove standard screws and replace with non-removable screws.
$13.79