SKU: 1870, 1870-SN
Finishes: Satin Nickel & Polished Brass
Secures door while allowing opening for viewing or ventilation
Steel chain
Easy to install
Instructions:
1. Mount long plate 1/4″ from edge of door at convenient height. Large hole at end of slot faces away from door jamb. Install 4 screws. (Drill 3/32″ pilot holes if necessary.)
2. Mount chain holder on door jamb so that knob on chain will reach hole in slide plate
$8.79
SKU: 1853, 1853-SN
Finishes: Polished Brass & Satin Nickel
Includes keeper for surface mount
Easy to install
Instructions:
1. Position bolt plate on door at desired location and mark screw holes. Drill 3/32″ diameter pilot holes 1/2″ deep and fasten bolt plate to door with screws.
2. Position strike plate on door jamb over bolt, making sure bolt will slide into strike properly with bolt extended. mark screw hole locations. Drill 3/32″ diameter pilot holes 1/2″ deep and fasten strike plate to jamb with screws.
$11.99
SKU: 1849, 1849-SN
Finishes: Polished Brass & Satin Nickel
For flush or recessed doors
Bolts surface mounts to face of door
2 keepers allow for surface or mortise frame installation
Instructions:
1. Position bolt at desired point on door and mark location of screws.
2. Close door and extend bolt. Mark position of bolt on door frame.
3. Use bolt mark on door frame fro strike placement. Two types of strikes are provided; use appropriate strike for door type, recessed or flush. Mark screw holes and fasten strike in place with screws.
$15.99
SKU: 1847, 1847-SN
Finishes: Polished Brass & Satin Nickel
Material: Solid Brass
For flush or recessed doors
Bolt surface mounts to face of door
2 keepers allow for surface or mortise frame installation
Instructions:
1. Position bolt at desired point on door and mark location of screws.
2. Close door and extend bolt. Mark position of bolt on door frame.
3. Use bolt mark on door frame for strike placement. Two types of strikes are provided; use appropriate strike for door type, recessed or flush. Mark screw holes and fasten strike in place with screws.
$13.99
SKU: 1843
Finish: White
Locks or unlocks with flip action
No mortising required
Easy to install privacy lock
Instructions:
1. Position swing lock on the frame of the door at a convenient height. The lip should be curved towards the door frame.
2. Drill 3/32″ pilot holes 1/2″ deep and install large screws.
$4.49 – $4.59
SKU: 1172, 1172-SN, 1172-VB
Finishes: Polished Brass, Satin Nickel and Vintage Bronze
Helps maintain entry security
Covers lockset holes from 1/2″ to 2-1/8″
Fits doors to 1-3/4″ thick
Dimensions: 2-5/8″ diameter
Instructions:
1. Place door plate with cylinder extending into door hole.
2. Place other plate on opposite side of door with indentation facing door hole.
3. Insert screw through plate into cylinder and tighten.
$8.29
SKU: 1170, 1170-SN, 1170-SSS,
Finishes: Polished Brass, Satin Nickel, Solid Stainless Steel
Material: Solid Stainless Steel (SSS only)
Use with 2-1/8″ bore locks
Covers marred area around knob
Allows conversion of 2-3/8″ to 2-3/4″ backset
Dimensions: 3-1/2″ diameter
Instructions:
1. Remove lockset.
2. Place trim against door and reinstall lockset.
$6.39 – $9.39
SKU: 1165, 1165-SN
Finishes: Polished Brass and Satin Nickel
Reduces bore from 2-1/8″ to 1-1/2″
For use with some deadbolts and rim cylinders
Instructions:
1. Remove deadbolt from door.
2. Install trim against door and them reinstall deadbolt.
$7.29 – $9.19
SKU: 1148-PB, 1148-SN, 1148-VB
Finishes: Polished Brass, Satin Nickel & Vintage Bronze
Material: Steel
Glass Knobs
Latch is reversible to left or right handed door
Decorative passage latch for 2-3/8″
backset applications
Fits up to 1-1/2″ diameter bore
Dimensions: 2-1/2” diameter roses
Instructions:
1. Place square end of latch through 3/4″ hole in side of door. Install latch face by securing with wood screws. Note: If you find you have installed latch tongue in wrong direction for door jamb, grip sides of latch tongue with pliers, pull latch tongue out, turn to opposite side and let tongue snap back in place. Remove old strike plate. Install new strike plate into existing recess. Insert tow screws into face of strike plate and fasten securely. Tab may be adjusted forward with screwdriver to obtain firm latching.
2. Center rosettes over 3/4′ dia. hole and attach to door using 3/4″ wood screws provided. Place spindle through square drive in latch and thread knob onto spindle until they seat into rosettes. Back off 1/2 turn and tighten set screws onto spindle. Test for proper operation.
$38.99
SKU: 1141, 1141-SN
Finishes: Satin Nickel & Polished Brass
Material: Solid Brass
For old style passage locks
Screw mounted on door
Dimensions: 2-1/2″ diameter
Fits up to 1-1/2″ diameter bore
Instructions:
1. Remove door knob and old roses.
2. Replace with new roses by lining up the holes and attaching screws. Attach door knobs.
$10.59
SKU: 1140, 1140-SN
Finishes: Satin Nickel & Polished Brass
Knob pair with spindle
Use on various interior mortise type locksets or latch sets
Spindle size: 7mm
Instructions:
1. Remove old knobs and spindle.
2. Twist one knob onto spindle and slide through door. Twist other knob on other side of spindle.
$23.99
SKU: 1105, 1105-SN
Finishes: Polished Brass & Satin Nickel
Latch hold-back (prevents locking yourself out)
5-pin tumbler with hardened steel pins
1-1/4″ bore required
Spring latch for automatic locking
Door Thickness: 1-3/8″ to 2-1/4″
Key Blank: Weiser Blank WR2/WR3
Instructions:
1. At desired height bore the hole for the cylinder 1-1/4″ diameter, with center at a distance of 2-3/8″ from edge of door.
2. Insert cylinder and ring from he outside of door and place back plate on inside of door. Connect back plate to cylinder with two connecting screws. Cut screws to proper length relative to door thickness.
3. Cut off connecting bar so that it projects 3/8″ beyond inside of door.
4. Plack lock on door so that connecting bar enters slot. Mark holes. Remove lock and drill 1/8″ pilot holes. Attache lock to door by inserting screws through lock into door.
5. Place strike plate on door jamb. Mark holes. Remove strike plate and drill 1/8″ pilot holes.
6. As needed, use chisel to cut door jamb so that strike is flush with door jamb.
$37.09
SKU: 1063, 1064, 1065, 1065-SN, 1066
Finishes: Vintage Bronze, Antique Brass, Polished Brass, Satin Nickel & Chrome
Fits Standard size doors
Steel strike plate with adjustable tab
Replaces most residential exterior & interior strikes
Dimensions: 1-3/8″ x 2-1/4″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Place new strike on door jamb, centered with latch hole.
3. Install screws provided and adjust tab with screw driver for proper fit.
$4.49 – $5.09