Logo



Logo
  • Products
    • Adapter Plates & Covers
    • Bolts, Latches & Guards
    • Door Reinforcers
    • Drawer, Cabinet & Mailbox Locks
    • Patio & Window Locks
    • Replacement Knobs & Rosettes
    • Strike Plates & Latch Guards
    • SecureShield
    • Terms & Conditions
  • Smart Deadbolt
    • Product Information
    • FAQ
  • Security Facts
  • Contact Us
  • Cart
  • My Account

Chain Door Guard

    Home    Bolts, Latches & Guards    Chain Door Guard
View cart “Keyed Chain Door Guard” has been added to your cart.
1870-SN

$8.79

SKU: 1870, 1870-SN

Finishes: Satin Nickel & Polished Brass

Secures door while allowing opening for viewing or ventilation

Steel chain

Easy to install

Instructions:
1. Mount long plate 1/4″ from edge of door at convenient height. Large hole at end of slot faces away from door jamb. Install 4 screws. (Drill 3/32″ pilot holes if necessary.)
2. Mount chain holder on door jamb so that knob on chain will reach hole in slide plate

Proposition 65 Warning
Clear selection
Add to Compare
SKU: 1870. Categories: All Categories, Bolts, Latches & Guards.
Related Products
Double Cylinder Interlocking Deadbolt
All Categories

SKU: 1125

Finish: Brass Tone

5-pin tumbler with hardened steel pins

Dual single or double cylinder locking unit & strike

Locks door to jamb to prevent forced
entry

Door Thickness: 1-3/8″ to 2-1/4″

1-1/4″ bore required

Key Blank: Weiser Blank WR2/WR3

Instructions:
CAUTIONS: Do not unscrew small retaining screws at rear of cylinder. Use only dry lubricant (graphite) on locks. Keep away clear of foreign objects.

To Install:
1. Select convenient  height for lock and place template against edge of door.
2. Mark hole positions. Bore 1-3/8″ hole for cylinder where indicated. Note: Bore through door until tip of drill barely emerges from other side. Remove drill bit and complete hole by drilling from opposite side to reduce splintering.
3. Drill 3/32″ diameter holes 1/2″ deep from attachment screws.
4. Insert cylinder and trim ring from outside of door. Attach backplate with two connecting bolts. Note: If bolts are too long, saw or break at groove, using caution to avoid marring the thread.
5. Cut or break connecting bar so it projects 3/8″ to 1/2″ beyond the inside of the door.
6. Plack lock on door so connecting bar enters “X” slot in back of lock. Secure with large mounting screws.
7. Align strike carefully, using template as a guide. Draw outline of strike on door jamb trim and chisel wood away (mortise) so strike mates freely with locking bars.
8. Mark mounting homes for strike, dill pilot holes, and secure strike to door jamb with screws provided.


$46.99

Add to cart
Add to Compare
Dual Security Strike
All Categories

SKU: 1027

Finish: Polished Brass

For locks with 5-1/2″ to 6″ centers

Replaces standard latch & deadbolt
strikes with one piece security

Strengthens or repairs wood jambs

3″ screws attach to  wall stud for extra security

Dimensions: 1-5/8″ x 11″

Door Thickness: 1-3/4″ or thicker doors

Instructions:
1. Remove old strike
2. Position new strike in place and mark with a pencil the three mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install short screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike plate and retest.

Note: Check distance between door and frame when door is closed.
– If the gap is 1/4″ or more install strike on surface of frame.
– If the gap is less than a 1/4″ strike must be chiseled into the frame.


$14.99

Add to cart
Add to Compare
Jumbo Door Viewer 180 Degrees
All Categories

SKU: 2330

Finish: Polished Brass

Material: Solid Brass

180 degree viewing area

Easy to install in 1-1/8″ hole

Door Thickness: 1-3/8″ to 2″

Instructions:
1. Mark door viewer location at eye level and centered horizontally on door.
2. Drill 1/8″ pilot hole completely through door.
3. Drill 1-1/8″ hole halfway through door from each side.
4. Install lens from outside.
5. Tighten inside retaining ring.


$43.99

Add to cart
Add to Compare
STD A.S.A. Commercial Strike
All Categories

SKU: 1038

Finish: Stainless Steel

Use on wood or metal jambs

Works with most commercial Grade 1 lock sets

Dimensions: 1-1/4″ x 4-7/8″

Door Thickness: All

Instructions:
1. Remove old strike
2. Place strike on jamb, centered over latch hole.
3. Mark outline of strike on door jamb.
4. Using chisel, cut out area for strike 1/16″ deep.
5. Install screws.

 

Proposition 65 Warning


$8.09

Add to cart
Add to Compare
Heavy Duty Latch Guard
All Categories

SKU: 1089, 1089-SSS

Finishes: Polished  Brass 

Out-swinging doors only

Secures against forced entry

Protects latch or bolt

Residential or commercial use

Dimensions: 3″ x 7″

Backset: Locksets with 2-3/4″ backset

Instructions:
1. Place latch guard on door and center on lock.
2. Mark center of mounting holes.
3. Drill two 3/8″ holes through door.
4. Install bolts, washers and nuts. Tighten securely.


$13.79

Select options
Add to Compare


About Us

First Watch Security, a division of Belwith Products, LLC. has been designing, manufacturing, and delivering home security products since 1959.

Today, First Watch Security is one of the most recognized brands in the market, producing products for home and commercial use.

Contact Us
  • +1.800.235.9484
  • 3100 Broadway Ave. SW Grandville, MI 49418
Connect With Us
  • Facebook
  • Twitter
  • Linkedin
Proposition 65 Warning

First Watch Security is an operating division of Belwith Products, LLC. | © 2015 Belwith Products, LLC. | All rights reserved.