SKU: 1253-604
Finish: Aluminum Tone
Securely locks in closed or vented
position
Assembled with hardened steel bolt
Easily activated with foot
Locks/unlocks with key
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$10.59
SKU: 1251
Finish: Aluminum Tone
Securely locks in closed or vented
position
Assembled with hardened steel bolt
Easily activated with foot
$5.69
SKU: 1185
Finish: Aluminum
Locks window or door in closed or vented position
For use on sliding windows or sliding
doors
Extruded aluminum with two steel
thumbscrews
Instructions:
To Lock:
1. Close window securely.
2. Plack lock against edge of sliding window on bottom track and tighten thumb screw.
To Vent:
1. Open sliding window 1-1/2″ to 2″. Place lock against edge of sliding window on bottom track and tighten thumb screw.
$2.59
SKU: 1088
Finish: Aluminum
Secures against forced entry
Requires some mortising
Mounts to door for out-swing application
or to door frame for in-swing application
Instructions:
1. Place latch guard on door, center on latch
2. Mark center of mounting holes.
3. Drill two 1/8″ holes for screws
4. Install 2 screws. Tighten securely.
5. Test with door in closed position, if door closes properly install additional 2 screws.
Note: If latch guard contacts strike lip, bend in slightly with hammer (adjust as needed).
$8.19
SKU: 1978
Finish: Aluminum
Spring loaded, slide-in action securely locks door in closed or vented position.
Prevents lifting or sliding of door
Easy to install
$4.49
SKU: 1970
Finish: Aluminum
For sliding doors & windows
Locks in closed or vented position
Hardened steel pin locks into retaining ring
Easy to install
$2.99
SKU: 1941
Finish: Aluminum
Cam action lock
Locks windows in closed or vented position
Instructions:
1. Place lock on track against window frame.
2. Press down on lever to lock.
3. For loose fitting doors, it may be necessary to place lock inside top track. Press on lever to lock.
$3.99
SKU: 1409
Finish: Aluminum
Locks window in closed or vented position
For use on sliding windows
Extruded aluminum with steel thumbscrew
Instructions:
To Lock:
1. Close window securely.
2. Plack lock against edge of sliding window on bottom track and tighten thumb screw.
To Vent:
1. Open sliding window 1-1/2″ to 2″. Place lock against edge of sliding window on bottom track and tighten thumb screw.
$2.79
SKU: 1408
Finish: Aluminum
Extruded aluminum with no-mar vinyl inserts to protect track
Locks window in closed or vented position
Fits wide & narrow type tracks
For use on sliding windows
Instructions:
To Lock:
1. Close window securely.
2. Placke lock against edge of sliding window on bottom track and turn wing clockwise until wedge is tight.
To Vent:
1. Open sliding window 1-1/2″ to 2″. Place lock against edge of sliding window on bottom track and turn wing nut clockwise until wedge is tight.
$3.09 – $4.79
SKU: 1275
Finish: Aluminum
For sliding door opening 28″- 52″
Telescoping aluminum locking bar
No cutting needed
Easy installation
Instructions:
To install inside sliding door:
1. Place rotating bracket on wall next to stationary door.
2. Mark and drill 1/8″ diameter holes and attach bracket to wall with screws provided.
3. With other end of bar in locking saddle, extend bar to inside edge of sliding door. Hold in horizontal position and mark and drill 1/8″ holes. Install screws through saddle catch into door.
To install outside sliding door:
1. Install jamb and bracket against inside edge of non-moving door.
2. Locking saddle install on inside frame of moveable door. Caution: Care must be taken that locking saddle is positioned at least 2″ above the sliding door handle.
$18.09
SKU: 1253
Finish: Aluminum Tone
Securely locks in closed or vented position
Assembled with hardened steel bolt
Easily activated with foot
Locks and unlocks with key
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
Instructions:
CAUTION: Before installation, check with patio door manufacturer for door specifications. Failure to do so may result in glass breakage!
1. Close sliding door completely.
2. With bolt retracted, place lock in desired position at top or bottom of leading edge of sliding door, leaving enough room to clear track so door slides smoothly.
3. Tap back of lock lightly with hammer to mark bolt hole position; remove lock. Make sure drill will clear glass. Drill 1-1/32″ diameter hole for locking bolt.
4. With bolt extended, position lock and slide bolt into hole. mark screw holes, remove lock and drill 1/8″ diameter holes.
5. Replace lock; install with standard screws and tighten. Or, to make door tamper-proof, remove standard screws and replace with non-removable screws.
$10.59