$19.99
SKU: 1150
Finish: Polished Brass
Zinc housing
5-pin tumbler lock
1-1/4″ bore hole required
Replacement lock cylinder for rim cylinder type lock sets
Key Blank: Weiser Blank WR5
Instructions:
1. Remove screws from old cylinder and remove cylinder.
2. Align connecting spindles of replacement cylinder to lock.
3. Insert screws into cylinder and tighten.
In stock
Add to Compare
SKU: 1005
Finish: Polished Brass
Fits standard size doors
Mortising required
Screws at base of box strike secure to
2″ x 4″ framing for added security
Dimensions: 1-1/4″ x 4-7/8″
Door Thickness: All
Instructions:
1. Mark center of bolt on frame.
2. Cut out template (see insert), locate center mark on template with center mark on frame. Tape in place.
3. Draw around outside of template. Mark 4 holes through template. Drill 1″ holes per template.
4. Chisel out between 1″ holes and fit strike box.
5. Chisel out 1/8″ deep for strike.
6. Install strike and faceplate with top and bottom screws. (Be sure 2 holes in strike box are toward center of frame.)
7. Drill two 1/8″ pilot holes at bottom of strike box toward center of frame and install screws at an angle.
$12.99
SKU:1846
Finish: Chrome
Ideal for hotel/motel doors & drawers
Provides extra security to almost any
door
Locks & unlocks from inside with key
Uses door strike opening for mount point
Hook to catch strike plate on door or lip of cabinet
Instructions:
1. Using key, unlock travel lock and slide out locking bar.
2. Open door or drawer and hook locking bar into strike plate or onto inside lip of cabinet.
3. Close door or drawer and slide locking plate onto bar either horizontally or vertically as desired.
4. Slide lock onto locking bar tight against locking plate. Use key to lock and unlock.
$27.99
SKU: 1027
Finish: Polished Brass
For locks with 5-1/2″ to 6″ centers
Replaces standard latch & deadbolt
strikes with one piece security
Strengthens or repairs wood jambs
3″ screws attach to wall stud for extra security
Dimensions: 1-5/8″ x 11″
Door Thickness: 1-3/4″ or thicker doors
Instructions:
1. Remove old strike
2. Position new strike in place and mark with a pencil the three mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install short screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike plate and retest.
Note: Check distance between door and frame when door is closed.
– If the gap is 1/4″ or more install strike on surface of frame.
– If the gap is less than a 1/4″ strike must be chiseled into the frame.
$22.99
SKU: 1106
Finish: White
Latch hold-back (prevents locking
yourself out)
5-pin tumbler with hardened steel pins
Door Thickness 1-3/8″ to 2-1/4″
1-1/4” bore required
Spring latch for automatic locking
Instructions:
1. At desired height bore the hole for the cylinder 1-1/4″ diameter, with center at a distance of 2-3/8″ from edge of door.
2. Insert cylinder and ring from the outside of door and place back plate on inside of door. Connect back plate to cylinder with two connecting screws. Cut screws to proper length relative to door thickness.
3. Cut off connecting bar so that it projects 3/8″ beyond inside of door.
4. Place lock on door so that connecting bar enters slot. Mark holes. Remove lock and drill 1/8″ pilot holes. Attache lock to door by inserting screws through lock into door.
5. Place strike plate on door jamb. Mark holes. Remove strike place and drill 1/8″ pilot holes.
6. As needed, use chisel to cut door jamb so that strike is flush with door jamb.
$54.99
