$19.99
SKU:1848
Finish: Polished Brass
For flush or recessed doors
Bolt surface mounts to face of door
2 keepers allow for surface or mortise
frame installation
Guide brackets adjust fit unique
installation conditions
In stock
Add to Compare
SKU: 1025, 1025-SSS, 1025-VB
Finishes: Polished Brass, Solid Stainless Steel & Vintage Bronze
Fits standard size doors
Strengthens or repairs wood jambs
3″ screws attach to wall stud for extra security
Dimensions: 1-1/4″ x 8″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Position new strike in place and mark the two mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or if a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install small screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike place and retest.
$17.99
SKU: 1035, 1036
Finish: Polished Brass & Chrome
Fits standard size doors
Use on wood or metal jambs
Dimensions: 4-7/8″ long, 3-3/8″ lip
Door Thickness: All
Instructions:
1. Place strike on jamb, centered over latch hole.
2. Mark outline of strike on door jamb.
3. Using chisel, cut out area for strike 1/16″ deep.
4. Install screws.
$9.99
SKU: 1862
Finish: Vintage Bronze
Secures door while allowing opening for
viewing or ventilation
Solid Brass material with steel chain
Easy to install
Instructions:
1. Mount long plate 1/4″ from edge of door at convenient height. Large hole at end of slot faces away from door jamb. Install 4 screws. (Drill 3/32″ pilot holes if necessary.)
2. Mount chain holder on door jamb so that knob on chain will reach hole in slide plate.
$19.99
SKU: 1120
Finish: Polished Brass
5-pin tumbler with hardened steel pins
Single cylinder locking unit & strike
Locks door to jamb to prevent forced entry
1-1/4″ bore required
Door Thickness: 1-3/8″ to 2-1/4″
Key Blank: Weiser Blank WR2/WR3
Instructions:
CAUTION: Do not unscrew small retaining screws at rear of cylinder. Use only dry lubricant (graphite) on lock. Keep keyway clear of foreign objects.
1. Select convenient height for lock and place template against edge of door.
2. Mark hole positions. Bore 1-3/8″ hole for cylinder where indicated. Note: Bore through door until tip of drill barely emerges from other side. Remove drill bit and complete hole by drilling from opposite side to reduce splintering.
3. Drill 3/32″ diameter holes 1/2″ deep for attachment screws.
4. Insert cylinder and trim ring from outside of door. Attache backplate with two connecting bolts. Note: If bolts are too long, saw or break at groove, using caution to avoid marring the thread.
5. Cut or break connecting bar so it projects 3/8″ to 1/2″ beyond the inside of the door.
6. Plack lock on door so connecting bar enters “X” slot in back of lock. Secure with large mounting screws.
7. Align strike carefully, using template as a guide. Draw outline of strike on door jamb trim and chisel wood away (mortise) so strike mates freely with locking bars.
8. Mark mounting holes for strike, drill pilot holes, and secure strike to door jamb with screws provided.
$51.99
SKU:1800
Finish: Polished Brass
Can be unlocked with key from inside or outside
Bolt slides into keyed mechanism to lock
Secures door while allowing 2″ opening or viewing or ventilation
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$30.99
Notifications
