$5.79
SKU: 2311
Finish: Polished Brass
Material: Solid Brass
160 degree viewing area
Easy to install in 1/2″ hole
Door Thickness: 1-3/8″ to 2″
Instructions:
1. Mark door viewer location at eye level and centered horizontally on door.
2. Drill 1/8″ pilot hole completely thorough door.
3. Drill 1/2″ hole halfway through door from each side.
4. Install lens from outside.
5. Tighten inside retaining ring.
In stock
Add to Compare
SKU: 1879
Finish: Polished Brass
Additional security of sliding dead bolt
Secures door while allowing opening for viewing or ventilation
Instructions:
1. Mount side place with sliding bolt inside on door at convenient height. Edge of slide place should be flush with door edge. Install four screws.
2. Mount strike place on door jamb so that sliding bolt engages the hole when door is fully closed. If door fit is tight, chisel out a recess on jamb for the strike plate. Install two screws.
3. Mount chain holder on jamb so that knob on chain will reach the hole in the slide plate when bolt is retracted. Mark and drill three pilot holes 3/32″ diameter and 1-1/4″ deep. Install chain holder with three screws.
$8.49
SKU: 1851, 1851-SN
Finishes: Polished Brass and Satin Nickel
Material: Solid Brass
For flush or recessed doors
Bolt surface mounts to face of door
2 keepers allow for surface or mortise frame installation
Instructions:
1. Position bolt at desired point on door and mark location of screws.
2. Close door and extend bolt. Mark position of bolt on door frame.
3. Use bolt mark on door frame for strike placement. Two types of strikes are provided; use appropriate strike for door type, recessed or flush. Mark screw holes and fasten strike in place with screws.
$9.29
SKU: 1125
Finish: Brass Tone
5-pin tumbler with hardened steel pins
Dual single or double cylinder locking unit & strike
Locks door to jamb to prevent forced
entry
Door Thickness: 1-3/8″ to 2-1/4″
1-1/4″ bore required
Includes tamper-resistant shutter guard
Key Blank: Weiser Blank WR2/WR3
Instructions:
CAUTIONS: Do not unscrew small retaining screws at rear of cylinder. Use only dry lubricant (graphite) on locks. Keep away clear of foreign objects.
To Install:
1. Select convenient height for lock and place template against edge of door.
2. Mark hole positions. Bore 1-3/8″ hole for cylinder where indicated. Note: Bore through door until tip of drill barely emerges from other side. Remove drill bit and complete hole by drilling from opposite side to reduce splintering.
3. Drill 3/32″ diameter holes 1/2″ deep from attachment screws.
4. Insert cylinder and trim ring from outside of door. Attach backplate with two connecting bolts. Note: If bolts are too long, saw or break at groove, using caution to avoid marring the thread.
5. Cut or break connecting bar so it projects 3/8″ to 1/2″ beyond the inside of the door.
6. Plack lock on door so connecting bar enters “X” slot in back of lock. Secure with large mounting screws.
7. Align strike carefully, using template as a guide. Draw outline of strike on door jamb trim and chisel wood away (mortise) so strike mates freely with locking bars.
8. Mark mounting homes for strike, dill pilot holes, and secure strike to door jamb with screws provided.
$36.09
SKU: 1106
Finish: White
Latch hold-back (prevents locking
yourself out)
5-pin tumbler with hardened steel pins
Door Thickness 1-3/8″ to 2-1/4″
1-1/4” bore required
Spring latch for automatic locking
Instructions:
1. At desired height bore the hole for the cylinder 1-1/4″ diameter, with center at a distance of 2-3/8″ from edge of door.
2. Insert cylinder and ring from the outside of door and place back plate on inside of door. Connect back plate to cylinder with two connecting screws. Cut screws to proper length relative to door thickness.
3. Cut off connecting bar so that it projects 3/8″ beyond inside of door.
4. Place lock on door so that connecting bar enters slot. Mark holes. Remove lock and drill 1/8″ pilot holes. Attache lock to door by inserting screws through lock into door.
5. Place strike plate on door jamb. Mark holes. Remove strike place and drill 1/8″ pilot holes.
6. As needed, use chisel to cut door jamb so that strike is flush with door jamb.
$16.49
SKU: 1025, 1025-SSS, 1025-VB
Finishes: Polished Brass, Solid Stainless Steel & Vintage Bronze
Fits standard size doors
Strengthens or repairs wood jambs
3″ screws attach to wall stud for extra security
Dimensions: 1-1/4″ x 8″
Door Thickness: All
Instructions:
1. Remove old strike.
2. Position new strike in place and mark the two mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or if a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install small screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike place and retest.
$7.89 – $11.29
