Logo



Logo
  • Products
    • Adapter Plates & Covers
    • Bolts, Latches & Guards
    • Door Reinforcers
    • Drawer, Cabinet & Mailbox Locks
    • Patio & Window Locks
    • Replacement Knobs & Rosettes
    • Strike Plates & Latch Guards
    • SecureShield
  • Smart Deadbolt
    • Product Information
    • FAQ
  • Security Facts
  • Contact Us
  • Cart
  • My Account

Door Reinforcer, Backset 2-3/8″ Door Thickness 1-3/4″

    Home    All Categories    Door Reinforcer, Backset 2-3/8″ Door Thickness 1-3/4″
2081_VB

$14.79 – $15.49

SKU: 2081-AB, 2081-PB, 2081-SSS, 2081-VB

Finishes: Antique Brass, Polished Brass, Solid Stainless Steel & Vintage Bronze

Material: Solid Brass (AB, PB, VB) Solid Stainless Steel (SSS)

Strengthens and repairs damaged doors

Assists in preventing forced entry

Dimensions: 4-1/4″ x 4-1/2″

Backset: 2-3/4″

Door Thickness: 1-3/4″

Proposition 65 Warning
Clear selection
Add to Compare
SKU: 2081. Category: All Categories.
Related Products
Mortise Trim Plates – 2 Pack
All Categories

SKU: 1142

Finish: Polished Brass

Pair with screws

Use on various bit key mortise locksets

Instructions:
1. Remove old plates from door.
2. Align plate over holes and attach screws provided.


$7.99

Add to cart
Add to Compare
Night Bolt & Locking Cylinder
All Categories

SKU: 1110, 1110-SN

Finish: Brass Tone & Satin Nickel

5-pin tumbler with hardened steel pins

1-1/4″ bore required

Door Thickness: 1-3/8″ to 2-1/4″

Key Blank: Weiser Blank WR2/WR3

Instructions:
1. At desired height bore the hole for the cylinder 1-1/4″ dimeter, with center at a distance of 2-3/8″ from edge of door.
2. Insert cylinder and ring from the outside of door and place back plate on inside of door. Connect back plate to cylinder with two connecting screws. Cut screws to proper length relative to door thickness.
3. Cut off connecting bar so that it projects 3/8″ beyond inside of door.
4. Plack lock on door so that connecting bar enters slot. Mark holes. Remove lock and drill 1/8″ pilot holes. Attach lock to door by inserting screws through lock into door.
5. Plack strike plate on door jamb lower than centerline of lock to allow for any sag in door. Mark holes. Remove strike plate and drill 1/8″ pilot holes.
6. As needed, chisel (mortise) long lip into door jamb and leave short lip on surface.


$20.29 – $20.59

Select options
Add to Compare
Adjustable Strike
All Categories

SKU: 1045

Finish: Polished  Brass

1/4″ adjustment for tight fit of door to frame

Stops door rattle

Assures engagement of dead latch function

Residential or commercial frames

Dimensions: 1-1/4″ x 2-3/4″

Door Thickness: All

Instructions:
Before starting first check door thickness for proper template alignment and then follow installation instructions.
-If door thickness is 1-3/4″ place template frame 3/16″ from door jamb.
-If door thickness is 1-3/8″ place template on the door jamb.

Installation Instructions:
1. Remove old strike.
2. Center template with latch hole and tape in place.
3. Position new strike in place and mark two holes. Chisel out area behind strike if needed or a flush fit is desired.
4. Drill 1/8″ pilot holes 2″ deep. Adjust to fit door.


$3.69

Add to cart
Add to Compare
STD A.S.A. Commercial Strike
All Categories

SKU: 1038

Finish: Stainless Steel

Use on wood or metal jambs

Works with most commercial Grade 1 lock sets

Dimensions: 1-1/4″ x 4-7/8″

Door Thickness: All

Instructions:
1. Remove old strike
2. Place strike on jamb, centered over latch hole.
3. Mark outline of strike on door jamb.
4. Using chisel, cut out area for strike 1/16″ deep.
5. Install screws.

 

Proposition 65 Warning


$7.09

Add to cart
Add to Compare
Security Latch Strike
All Categories

SKU: 1025, 1025-SSS, 1025-VB

Finishes: Polished  Brass, Solid Stainless Steel & Vintage Bronze

Fits standard size doors

Strengthens or repairs wood jambs

3″ screws attach to wall stud for extra security

Dimensions: 1-1/4″ x 8″

Door Thickness: All

Instructions:
1. Remove old strike.
2. Position new strike in place and mark the two mounting holes on the side of the strike away from the door jamb. Chisel out area behind strike if needed or if a flush fit is desired.
3. Drill 1/8″ pilot holes 1″ deep. Install small screws.
4. Close door and operate lock. If lock operates correctly, drill remaining two pilot holes with a 1/8″ drill bit 2″ deep. Install long screws. If lock does not operate correctly, reposition strike place and retest.


$7.89 – $11.29

Select options
Add to Compare


About Us

First Watch Security, a division of Belwith Products, LLC. has been designing, manufacturing, and delivering home security products since 1959.

Today, First Watch Security is one of the most recognized brands in the market, producing products for home and commercial use.

Contact Us
  • +1.800.235.9484
  • 3100 Broadway Ave. SW Grandville, MI 49418
Connect With Us
  • Facebook
  • Twitter
  • Linkedin
Proposition 65 Warning

First Watch Security is an operating division of Belwith Products, LLC. | © 2015 Belwith Products, LLC. | All rights reserved.