$18.49
SKU: 1532
Finish: Polished Brass
Material: Solid Brass
Rim mortise & surface strikes included
3 different keepers for special mounting
applications
For use on old style casement windows
Rim Strike Installation:
1. Place fastener in desired location and secure loosely with four screws.
2. Place rim strike in position to line up with fastener and install with two screws.
3. Check operation of fastener with strike and tighten all screws.
Mortise Strike Installation:
1. Place fastener in desired location and secure loosely with four screws.
2. Place mortise strike in position to line up with fastener. Mark position of screw holes, strike, and mortise hole using 3/16″ diameter drill and mortise 3/4″ deep recess. Install mortise strike with two screws.
3. Check operation of fastener with strike and tighten all screws.
Surface Strike Installation:
1. Place fastener in desired location and secure loosely with four screws.
2. Place surface strike in position to line up with two screws.
3. Check operation and tighten all screws.
In stock
Add to Compare
SKU: 1418
Finish: Polished Brass
Mounts on vertical track
Locks in closed or vented position
Flips away to allow window to open
Instructions:
1. Close window and attach lock 3″ to 4″ above top of lower sash with nails enclosed.
2. Swing stop closed to engage window stop, preventing window from being raised past window stop.
$3.09
SKU: 1404
Finish: White
For wood, aluminum, & vinyl double hung windows
Locks & unlocks with key
Cam action draws windows together to prevent drafts
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
$10.09
SKU: 1185
Finish: Aluminum
Locks window or door in closed or vented position
For use on sliding windows or sliding
doors
Extruded aluminum with two steel
thumbscrews
Instructions:
To Lock:
1. Close window securely.
2. Plack lock against edge of sliding window on bottom track and tighten thumb screw.
To Vent:
1. Open sliding window 1-1/2″ to 2″. Place lock against edge of sliding window on bottom track and tighten thumb screw.
$2.59
SKU: 1276
Finish: White
For sliding door opening 28″- 52″
Telescoping aluminum locking bar
No cutting needed
Easy installation
Instructions:
To install inside sliding door:
1. Place rotating bracket on wall next to stationary door.
2. Mark and drill 1/8″ diameter holes and attach bracket to wall with screws provided.
3. With other end of bar in locking saddle, extend bar to inside edge of sliding door. Hold in horizontal position and mark and drill 1/8″ holes. Install screws through saddle catch into door.
To install outside sliding door:
1. Install jamb and bracket against inside edge of non-moving door.
2. Locking saddle install on inside frame of moveable door. Caution: Care must be taken that locking saddle is positioned at least 2″ above the sliding door handle.
$19.89
SKU: 1253
Finish: Aluminum Tone
Securely locks in closed or vented position
Assembled with hardened steel bolt
Easily activated with foot
Locks and unlocks with key
Key Blank: Briggs & Stratton B1 & Yale Blank Y13
Instructions:
CAUTION: Before installation, check with patio door manufacturer for door specifications. Failure to do so may result in glass breakage!
1. Close sliding door completely.
2. With bolt retracted, place lock in desired position at top or bottom of leading edge of sliding door, leaving enough room to clear track so door slides smoothly.
3. Tap back of lock lightly with hammer to mark bolt hole position; remove lock. Make sure drill will clear glass. Drill 1-1/32″ diameter hole for locking bolt.
4. With bolt extended, position lock and slide bolt into hole. mark screw holes, remove lock and drill 1/8″ diameter holes.
5. Replace lock; install with standard screws and tighten. Or, to make door tamper-proof, remove standard screws and replace with non-removable screws.
$10.59
